1、Designation:F107487(Reapproved 2012)An American National StandardStandard Specification forCleats,Welded Horn Type1This standard is issued under the fixed designation F1074;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of
2、last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers hollow cleats and pads formarine use.1.2 The cleats shall be used where securing of boat handling
3、lines are required onboard commercial and navy boats andcrafts.1.3 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA370 Test Met
4、hods and Definitions for Mechanical Testingof Steel ProductsA385 Practice for Providing High-Quality Zinc Coatings(Hot-Dip)3.Ordering Information3.1 Orders for material under this specification shall includethe following:3.1.1 Title,number,and date of this specification,3.1.2 Quantity,3.1.3 Size of
5、cleats,and3.1.4 Packaging,packing,or marking requirements.4.Materials and Manufacture4.1 Material:4.1.1 The horn cleats shall be of galvanized steel,grade1023W,in accordance with Practice A385.4.1.2 The base plate shall be of steel,(carbon 0.35maximum),in accordance with Specification A36/A36M.4.1.3
6、 All chafing surfaces shall have a 125 finish.4.2 ManufactureThe cleats horns shall be of cast steel,round in shape,and free of burrs or sharp edges.The hornsshall be welded to a base plate as shown in Fig.1(see Table 1).The weld is to be ground smooth to prevent chafing of ropes.The base plate shal
7、l be oval shaped with smooth roundededges.The dimensions shall be in accordance with Table 1.5.Packaging5.1 The packing shall afford protection against deteriorationand physical damage during shipment from the manufacturer tothe using activity for immediate use.6.Product Marking6.1 Containers shall
8、be stenciled with the ASTM standarddesignation,in black paint with approximately 1 in.(25.4 mm)high letters and numbers with the following information:6.1.1 Address,6.1.2 purchase order number,and6.1.3 Manufacturers name.7.Keywords7.1 base plates;boat handling lines;cleats;hollow cleats;horn cleats;
9、marine;marine cleats;ship;welded cleats1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved June 1,2012.Published October 2012.Originallyappro
10、ved in 1987.Last previous edition approved in 2007 as F1074-87(2007).DOI:10.1520/F1074-87R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summa
11、ry page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 NOTE1See Table 1 for dimensions.FIG.1Welded Horn Type Cleat(16 in.)F1074 87(2012)2 SUPPLEMENTARY REQUIREMENTSThe following supplementary requirement shall apply on
12、ly when specified by the purchaser in thecontract or order.S1.Quality Assurance ProvisionsS1.1 Responsibility for InspectionThe purchaser reservesthe right to perform any of the inspections set forth in thespecification where such inspections are deemed necessary toassure that supplies and services
13、conform to prescribed require-ments.S1.2Source InspectionThe purchaser reserves the rightto inspect the manufacturing process and end product in thesuppliers plant.S1.3 TestsThe cleats shall meet the test load requirementsof Table 1,as tested in accordance with Test Methods andDefinitions A370.ASTM
14、International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirel
15、y their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised,either reapproved or withdrawn.Your comments are invited either for revision of this standard or for additional standardsand shou
16、ld be addressed to ASTM International Headquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,which you may attend.If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards,at the address shown below.This standard is copyrighted by ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959,United States.Individual reprints(single or multiple
