1、Designation:F107294(Reapproved 2012)An American National StandardStandard Specification forExpanded-Metal Doors1This standard is issued under the fixed designation F1072;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of las
2、t revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers steel expanded-metal doorssuitable for installation in expanded-metal bulkheads,struc-tural bulkhead
3、s,and structural arches.1.2 The values stated in inch-pound units are to be regardedas the standard.The values given in parentheses are forinformation only.2.Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA167 Specification for Stainless and Heat-ResistingC
4、hromium-Nickel Steel Plate,Sheet,and StripD3951 Practice for Commercial PackagingF783 Specification for Staple,Handgrab,Handle,and Stir-rup Rung2.2 Other Documents:ABS Rules for Building and Classing Steel Vessels3AWS D1.1 Structural Welding Code43.Classification3.1 Expanded-metal doors are furnishe
5、d in four types(seeDetail“J”)as follows:3.1.1 Type IRight hand(RH).3.1.2 Type IILeft hand(LH).3.1.3 Type IIIRight hand reverse(RHR).3.1.4 Type IVLeft hand reverse(LHR).4.Ordering Information4.1 Orders for doors under this specification shall includethis specification number and type.5.Materials and
6、Manufacture5.1 MaterialsSee Table 1.5.2 Manufacture:5.2.1 Doors shall be furnished with the vertical supportchannels and top angle in place.A temporary brace shall beincluded at the frame bottom to prevent racking.5.2.2 Welding shall be in accordance with AWS D1.1Structural Welding Code or ABS Rules
7、 for Building andClassing Steel Vessels.6.Installation Requirements6.1 Doors shall be fitted with rubber-tipped bumpers and amanually operated catch for holding doors in an open position.These shall be furnished and installed by others.6.2 Provision shall be made for the installation of a rim latchs
8、et operated by knobs on both sides.This hardware shall befurnished and installed by others.6.3 Padlocks shall be furnished by others.6.4 Any holes needed in the frame for installation inexpanded-metal or other types of bulkheads shall be made atinstallation by others.7.Dimensions and Tolerances7.1 D
9、imensions are as indicated in Figs.1-8 and Table 1.7.2 Tolerance6116in.(1.5 mm).8.Workmanship,Finish,and Appearance8.1 Doors and frames shall be free from all cracks,burrs,sharp edges,and other defects.8.2 The door manufacturer shall apply a nonhazardouscorrosion-inhibiting primer coating to all doo
10、r assemblies.9.Packaging and Package Marking9.1 Each expanded-metal door shall be individually packedfor shipment and storage in accordance with Practice D3951.9.2 In addition to any special marking required by thecontract or purchase order,each expanded-metal door shall bemarked in accordance with
11、Practice D3951.10.Keywords10.1 expanded-metal doors;expanded-metal bulkheads;metal doors;structural arches;structural bulkheads1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and De
12、ck Machinery.Current edition approved June 1,2012.Published October 2012.Originallyapproved in 1987.Last previous edition approved in 2006 as F1072 94(2006).DOI:10.1520/F1072-94R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.F
13、or Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping,ABS Plaza 16855 NorthchaseDr.,Houston,TX 77060.4Available from American Welding Society,550 N.W.Le Jeune Rd.,Miami,FL33126.Copyright ASTM Int
14、ernational,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 TABLE 1 Expanded-Metal Door MaterialsNOTE11 in.=25.4 mm.ItemNumberDescription1Frame TopAngle,6 3 516in.,Specification A36/A36M.2Frame SideChannel,C3 5.0,Specification A36/A36M.3StapleRound bar,Specification F
15、783.4Door FrameAngle,1 1 in.,Specification A36/A36M.5BraceFlat bar,2 in.,Specification A36/A36M.6Cross BraceFlat bar,2 in.,Specification A36/A36M.7StopFlat bar,4 in.,Specification A36/A36M.8PadFlat bar,4 in.,Specification A36/A36M.9HingeSwaged butt,plain,fixed pin,3-2-in.Type 316 stain-less steel,Sp
16、ecification A167.10Expanded Metal13-gage -in.flat pattern,SpecificationA36/A36M.11Temporary BraceAngle 1 1 in.,SpecificationA36/A36M.(See 5.2.1.)F1072 94(2012)2 NOTE11 in.=25.4 mm.FIG.1 Right-Hand Door and Frame AssemblyType I(Left Hand,Type II Not Shown)F1072 94(2012)3 NOTE11 in.=25.4 mm.FIG.2 Right-Hand Reverse Door and Frame AssemblyType III(Left Hand,Type IV Not Shown)F1072 94(2012)4 NOTE11 in.=25.4 mm.FIG.3 FrameNOTE11 in.=25.4 mm.FIG.4 DoorF1072 94(2012)5 NOTE11 in.=25.4 mm.FIG.5 PadNOTE11
