收藏 分享(赏)

ASTM_F_1097_-_17.pdf

上传人:益****师 文档编号:188551 上传时间:2023-03-04 格式:PDF 页数:5 大小:92.68KB
下载 相关 举报
ASTM_F_1097_-_17.pdf_第1页
第1页 / 共5页
ASTM_F_1097_-_17.pdf_第2页
第2页 / 共5页
ASTM_F_1097_-_17.pdf_第3页
第3页 / 共5页
ASTM_F_1097_-_17.pdf_第4页
第4页 / 共5页
ASTM_F_1097_-_17.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F109717An American National StandardStandard Specification forMortar,Refractory(High-Temperature,Air-Setting)1This standard is issued under the fixed designation F1097;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the y

2、ear of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers dry air-setting refractory mor-tar for use in laying and bonding refractory brick in ship

3、boilerfurnaces and wet air-setting refractory mortar for use in layingrefractory brick in stationary boiler furnaces,bright annealingfurnaces,controlled atmosphere furnaces,and furnaces heatedby electric elements.1.2 The values stated in inch-pound units are to be regardedas standard.The values give

4、n in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appr

5、o-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDeve

6、lopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C24 Test Method for Pyrometric Cone Equivalent(PCE)ofFireclay and High Alumina Refractory MaterialsC27 Classificati

7、on of Fireclay and High-Alumina RefractoryBrickC92 Test Methods for Sieve Analysis and Water Content ofRefractory MaterialsC133 Test Methods for Cold Crushing Strength and Modu-lus of Rupture of RefractoriesC198 Test Method for Cold Bonding Strength of RefractoryMortarC199 Test Method for Pier Test

8、for Refractory Mortars2.2 Federal Specifications3The following documents shallapply only when one or more of the requirements of Supple-mentary Requirement S1 are specified in the contract orpurchase order(see 4.1.3):UU-S-48 Sacks,Shipping,PaperPPP-B-704 Pails:Shipping,Steel(1 through 12 gallon)2.3

9、Military Standards3The following documents shallapply only when one or more of the requirements of Supple-mentary Requirement S1 are specified in the contract orpurchase order(see 4.1.3):MIL-STD-129 Marking for Shipment and StorageMIL-STD-147 Palletized Unit Loads2.4 ANSI/ASQ Standards:4Z1.4 Samplin

10、g Procedures and Tables for Inspection byAttributes3.Classification3.1 The refractory mortar shall be of the following types:3.1.1 Type 1Dry.3.1.2 Type 2Wet.4.Ordering Information4.1 Orders for material under this specification shall includethe following information,as necessary to adequately descri

11、bethe material:4.1.1 ASTM designation and year of issue,4.1.2 Type required(see 3.1),and4.1.3 Optional requirements,if any(see SupplementaryRequirement S1).5.Material5.1 The mortar shall be composed of finely ground heat-resistant clays,minerals,or a mixture of clays and minerals ineither a dry or w

12、et condition.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.07 onGeneral Requirements.Current edition approved Dec.1,2017.Published January 2018.Originallyapproved in 1991.Last previous edition ap

13、proved in 2012 as F1097 91(2012).DOI:10.1520/F1097-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available f

14、rom DLA Document Services,Building 4/D,700 Robbins Ave.,Philadelphia,PA 19111-5094,http:/quicksearch.dla.mil.4Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Co

15、nshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Org

16、anization Technical Barriers to Trade(TBT)Committee.1 5.1.1 Type 1,DryMortar shall be furnished dry and shallbe ready for use as soon as mixed with water.Mortar,afterbeing mixed with water and then dried,shall be capable ofbeing remixed with water.5.1.2 Type 2,WetMortar shall be furnished ready for useat a trowelling consistency and shall be easily mixed withwater to a dipping consistency.6.Performance Requirements6.1 Resistance to Heat SoakingMortar shall not soften norshow any evidence of fusi

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2