收藏 分享(赏)

ASTM_F_2764_-_F_2764M_-_11ae2.pdf

上传人:益****师 文档编号:188937 上传时间:2023-03-04 格式:PDF 页数:8 大小:136.58KB
下载 相关 举报
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第1页
第1页 / 共8页
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第2页
第2页 / 共8页
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第3页
第3页 / 共8页
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第4页
第4页 / 共8页
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第5页
第5页 / 共8页
ASTM_F_2764_-_F_2764M_-_11ae2.pdf_第6页
第6页 / 共8页
亲,该文档总共8页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F2764/F2764M11a2Standard Specification for30 to 60 in.750 to 1500 mm Polypropylene(PP)Triple WallPipe and Fittings for Non-Pressure Sanitary SewerApplications1This standard is issued under the fixed designation F2764/F2764M;the number immediately following the designation indicates the y

2、earof original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTERevised designation to correspond with units statement in Novembe

3、r 2013.2NOTETable 1 headings were editorially added in July 2014.1.Scope*1.1 This specification covers requirements and test methodsfor triple wall polypropylene pipe and fittings.The nominalinside diameters covered are 30 to 60 in.750 to 1600 mm.1.2 The requirements of this specification are intend

4、ed toprovide pipe and fittings suitable for underground use fornon-pressure sanitary sewer systems.Pipe and fittings pro-duced in accordance with this specification shall be installed incompliance with Practice D2321.1.3 This specification covers pipe and fittings with anessentially smooth interior

5、wall,an essentially smooth exteriorwall and an annular corrugated profile middle wall(Fig.1).1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independe

6、ntly of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.5 The following precautionary statement applies only toSection 7 of this specification.This standard does not purportto address all of the safety concerns,if any,associated with itsuse.It is the r

7、esponsibility of the user of this standard toestablish appropriate safety and health practices and deter-mine the applicability of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked AusteniticStainless Steel Sheet,Strip,Plate,

8、and Flat BarD256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating

9、 Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1600 Terminology forAbbreviated Terms

10、Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe

11、 by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D2990 Test Methods for Tensile,Compressive,and FlexuralCreep and Creep-Rupture of PlasticsD3212 Specification for Joints for Drain and Sewer Plas

12、ticPipes Using Flexible Elastomeric SealsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanning CalorimetryD4101 Specification for Polypropylene Injection and Extru-sion MaterialsD4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By

13、the Muffle-Furnace TechniqueD4389 Specification for Finished Glass Fabrics Woven FromRovings1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved May 1,2011.Published May

14、2011.Originallyapproved in 2010.Last previous edition approved in 2011 as F276411.DOI:10.1520/D2764_F2764M11AE01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the stan

15、dards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 D6992 Test Method for Accelerated Tensile Creep andCreep-Rupture of Geosynthet

16、ic Materials Based on Time-Temperature Superposition Using the Stepped IsothermalMethodF412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic PipeF2136 Test Method for Notched,Constant Ligament-Stress(NCLS)Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated Pipe2.2 AASHTO Standards:3LRFD,Section 12 AASHTO LRFD Bridge Design Specifi-cations Section 12 Buried Structures and Tunnel Liners2.3 Federal Stan

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2