1、Designation:F288111(Reapproved 2015)Standard Specification for12 to 60 in.300 to 1500 mm Polypropylene(PP)Dual WallPipe and Fittings for Non-Pressure Storm SewerApplications1This standard is issued under the fixed designation F2881;the number immediately following the designation indicates the year
2、oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers requirements and test methodsfor dual
3、wall polypropylene pipe and fittings.The nominalinside diameters covered are 12 to 60 in.300 to 1500 mm.1.2 The requirements of this specification are intended toprovide pipe and fittings suitable for underground use fornon-pressure storm sewer systems.Pipe and fittings producedin accordance with th
4、is specification shall be installed incompliance with Practice D2321.1.3 This specification covers pipe and fittings with aninterior smooth wall and an annular corrugated profile outerwall(Fig.1).1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as stand
5、ard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.5 The following precautionary statement caveat pertainsonly to the test method porti
6、on,Section 7,of this specification.This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prio
7、r to use.2.Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked AusteniticStainless Steel Sheet,Strip,Plate,and Flat BarD256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Metho
8、d for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1238 Test Method for Melt Flow Rates of Thermoplas
9、ticsby Extrusion PlastometerD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Underground Installation of Thermoplas
10、-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup(Falling Weight)D29
11、90 Test Methods for Tensile,Compressive,and FlexuralCreep and Creep-Rupture of PlasticsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanning CalorimetryD4101 Specificatio
12、n for Polypropylene Injection and Extru-sion MaterialsD4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By the Muffle-Furnace TechniqueD4389/D4389M Specification for Finished Glass FabricsWoven From RovingsD6992 Test Method for Accelerated Tensile Creep andCreep-Ru
13、pture of Geosynthetic Materials Based on Time-Temperature Superposition Using the Stepped IsothermalMethod1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approved Aug.1,2015.
14、Published November 2015.Originallyapproved in 2011.Last previous edition approved in 2011 as F288111.DOI:10.1520/F288111R15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer
15、to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 F412 Terminology Relating to Plastic Piping SystemsF477 Specification for Elastomeric Seals(Gaskets)for Join-ing Plastic Pipe2.2 AAS
16、HTO Standard:3LRFD,Section 12 AASHTO LRFD Bridge Design Specifi-cations Section 12 Buried Structures and Tunnel LinersM288 Geotextile Specification for Highway Applications2.3 Federal/Military Standards:4Fed.Std.No.123 Marking for Shipment(Civil Agencies)MIL-STD-129 Marking for Shipment and Storage3.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nology F412 and abbreviations are in accordance with Termi-nology D1600,unless otherwise specified.The abbreviation forpolypropylene
