收藏 分享(赏)

ASTM_F_3040_-_F_3040M_-_13_2018.pdf

上传人:益****师 文档编号:189227 上传时间:2023-03-04 格式:PDF 页数:4 大小:178.61KB
下载 相关 举报
ASTM_F_3040_-_F_3040M_-_13_2018.pdf_第1页
第1页 / 共4页
ASTM_F_3040_-_F_3040M_-_13_2018.pdf_第2页
第2页 / 共4页
ASTM_F_3040_-_F_3040M_-_13_2018.pdf_第3页
第3页 / 共4页
ASTM_F_3040_-_F_3040M_-_13_2018.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F3040/F3040M13(Reapproved 2018)An American National StandardStandard Test Method forMechanical Static Load Testing of Non-Structural MarineJoiner Bulkheads1This standard is issued under the fixed designation F3040/F3040M;the number immediately following the designation indicates the year

2、of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method describes a procedure for evaluatingthe stren

3、gth of non structural marine joiner of A,B,andC-Class bulkhead and liner systems.A,B,and C-class bulk-heads are defined and discussed in 2.1.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivale

4、nts;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this sta

5、ndard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on

6、 Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 International Maritime Organization Publication:SOLAS 2009 Consolidated Edition,Chapter II-2,Part A,Regulati

7、on 3,Definitions23.Summary of Test Method3.1 Install panels into a mounting test fixture representativeof the bulkhead system.3.2 Attach loading bracket to center panel at mid-width andheight of the center panel.3.3 Mount three dial indicators at the back side of the centerpanel to measure deflectio

8、n at the centerline of the panels threevertical quarter points.(See Fig.1.)3.4 Load the bracket at no more than 10 kg 22 lbincrements until a total load of 200 kg 441 lb is obtained.Record deflection from dial indicators at each incremental loador until failure is reached.3.5 If failure is not reach

9、ed,extend the loading bracketoutward to the next moment arm from the panel and repeatloading.3.6 Continue to increase applied load until failure or untilmaximum moment arm and loads are applied.4.Significance and Use4.1 The test method provides information regarding thebehavior of a non-structural A

10、,B,or C-Class bulkhead panelsystem under a static load.Test data for load,moment anddeformation is measured.4.2 Static load test of non-structural marine joiner panelsystems provide a standard method of obtaining data forresearch and development,quality control,acceptance orrejection under specifica

11、tions,and special purposes.The testscannot be considered significant for engineering design inapplications differing widely from the loading type and mag-nitude of the standard test.Such applications shall requireadditional tests.5.Apparatus5.1 Bulkhead Mounting FixtureSecures the edges of thepanels

12、 in a position representative of the bulkhead systeminstalled on a ship.The two edges on the side of the testspecimen shall be fitted with typical edge trim.Top and bottomshoes,and panel connection mechanism capable of supporting2135 6 3 mm 84 in.high by 3660 6 3 mm 144 in.minimum wide joiner panel

13、system shall be used.5.2 Loading BracketAttach the loading bracket throughthe bulkhead panel.The loading bracket has supports forloading at different distances,305 6 3 mm 12 in.,610 6 3mm 24 in.,and 915 6 3 mm 36 in.from the bulkhead panelsurface.The loading bracket bulkhead plate has four holes1Thi

14、s test method is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved April 1,2018.Published May 2018.Originallyapproved in 2013.Last previous edition approved in 20

15、13 as F3040/F3040M 13.DOI:10.1520/F3040_F3040M-13R18.2Available from International Maritime Organization,4 Albert Embankment,London,Se1 7SR,http:/www.imo.org.(Fifth Edition.)Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international

16、 standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 30563 mm 12 in.apart vertically and horizontally with theload centered vertically and horizontally between the two setsof holes.See Fig.2.5.3 Hook on Loading BracketSuspends load plates fromthe loading

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2