收藏 分享(赏)

ASTM_F_2838_-_10.pdf

上传人:益****师 文档编号:189229 上传时间:2023-03-04 格式:PDF 页数:6 大小:88.24KB
下载 相关 举报
ASTM_F_2838_-_10.pdf_第1页
第1页 / 共6页
ASTM_F_2838_-_10.pdf_第2页
第2页 / 共6页
ASTM_F_2838_-_10.pdf_第3页
第3页 / 共6页
ASTM_F_2838_-_10.pdf_第4页
第4页 / 共6页
ASTM_F_2838_-_10.pdf_第5页
第5页 / 共6页
ASTM_F_2838_-_10.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F283810Standard Practice forAccelerated Laboratory Aging of Radial Passenger Car andLight Truck Tires through Load Range E for the LaboratoryGeneration of Belt Separation1This standard is issued under the fixed designation F2838;the number immediately following the designation indicates

2、the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice describes a method to laboratory age a ne

3、wtire in an oven to produce changes in certain chemical andphysical properties at the belt edges similar to those of tiresin-service(see Appendix X1).1.2 This practice is a precursor to conducting an ASTMstandard roadwheel test method for laboratory generation ofbelt separation in radial passenger c

4、ar and light truck tires.1.3 This practice may not produce representative chemicaland physical property changes in any part of the tire except thebelt edge.1.4 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.5 This standard do

5、es not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For specificprecautionary statements,s

6、ee Section 8.2.Referenced Documents2.1 ASTM Standards:2ASTM SI10-02 IEEE/ASTM SI 10 American NationalStandard for Use of the International System of Units(SI):The Modern Metric SystemF538 Terminology Relating to the Characteristics and Per-formance of TiresG128 Guide for Control of Hazards and Risks

7、 in OxygenEnriched Systems2.2 Other Standards:ANSI/ISO/IEC 17025 General requirements for the compe-tence of testing and calibration laboratories3Compressed Gas Association(CGA)Standard for ValveConnections V-14EIGA IGA 04/09/E Fire Hazards of Oxygen and OxygenEnriched AtmospheresRMA Volume 4 Tire S

8、ervice Manual5Tire and Rim Association(T&RA)Year Book6European Tyre and Rim Technical Organisation(ETRTO)Standards ManualJapan Automobile Tyre Manufacturers Association Inc.(JATMA)Year BookISO 4000 Passenger Car Tyres and Rims73.Terminology3.1 Definitions:3.1.1 age,vto apply conditions so as to prom

9、ote change ofmaterial properties.3.1.1.1 DiscussionFor a tire,this can be done on aroadwheel,in a laboratory oven,in service,etc.3.1.2 aging,accelerated laboratory(also:aging,labora-tory),nincreased rate of tire material property changes underspecified conditions,including temperature,inflation pres

10、sure,oxygen concentration in the filling gas,and time.3.1.3 aging,in-service,nmaterial property changes withintires due to consumer usage.3.1.3.1 DiscussionSee Appendix X1 for more details.3.1.4 aging,oven,naccelerated laboratory aging in anelevated temperature environment.1This practice is under th

11、e jurisdiction of ASTM Committee F09 on Tires and isthe direct responsibility of Subcommittee F09.30 on Laboratory(Non-Vehicular)Testing.Current edition approved May 1,2010.Published June 2010.DOI:10.1520/F2838-10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Cust

12、omer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.4Available from Compressed Gas

13、Association(CGA),4221 Walney Rd.,5thFloor,Chantilly,VA 20151-2923,http:/.5Available from Rubber Manufacturers Association(RMA),1400 K St.,NW,Suite 900,Washington,DC 20005,http:/www.rma.org.6Available from Tire and RimAssociation,Inc.(TRA),175 Montrose WestAve.,Suite 150,Copley,OH 44313,http:/www.us-

14、tra.org.7Available from International Organization for Standardization(ISO),1,ch.dela Voie-Creuse,Case postale 56,CH-1211,Geneva 20,Switzerland,http:/www.iso.ch.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 3.1.5 aging,thermal oxidative

15、,nthe process wherebychemical and physical material properties of a tire change withexposure to heat and oxygen.3.1.6 belt,in a tire,na breaker that substantially restrictsthe carcass in a circumferential direction.F5383.1.7 belt separation,na breakdown of bonding betweenthe belts or plies or tread,

16、or combination thereof.F5383.1.8 cold inflation pressure,nthe gauge pressure of a tire,measured after equilibration at ambient temperature.3.1.9 inflation gas,nthe specific filling medium used topressurize the tire cavity and maintain a specified gaugepressure(for example,oxygen/nitrogen gas mixture,air).3.1.10 hot inflation pressure,nthe gauge pressure of a tireafter equilibration in an oven,measured between 60 and 80min after removal from oven.3.1.11 measured inflation pressure,ngauge pressure

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2