1、Designation:F2881/F2881M19Standard Specification for12 to 60 in.300 to 1500 mm Polypropylene(PP)Dual WallPipe and Fittings for Non-Pressure Storm SewerApplications1This standard is issued under the fixed designation F2881/F2881M;the number immediately following the designation indicates the yearof o
2、riginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This specification covers requirements and test methodsfor dual w
3、all polypropylene pipe and fittings.The nominalinside diameters covered are 12 to 60 in.300 to 1500 mm.1.2 The requirements of this specification are intended toprovide pipe and fittings suitable for underground use fornon-pressure storm sewer systems.Pipe and fittings producedin accordance with thi
4、s specification shall be installed incompliance with Practice D2321.1.3 This specification covers pipe and fittings with aninterior smooth wall and an annular corrugated profile outerwall(Fig.1).1.4 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standa
5、rd.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in non-conformance with the standard.1.5 The following precautionary statement caveat pertainsonly to the test method portio
6、n,Section 8,of this specification.This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety,health,and environmental practices and determine the appli-cability of regulatory
7、limitations prior to use.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organizat
8、ion TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A666 Specification for Annealed or Cold-Worked AusteniticStainless Steel Sheet,Strip,Plate,and Flat BarD256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning
9、 Plastics for TestingD638 Test Method for Tensile Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD792 Test Methods for Density and Specific Gravity(Rela-tive Density)of Plastics by DisplacementD1238 Test Meth
10、od for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1505 Test Method for Density of Plastics by the Density-Gradient TechniqueD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2321 Practice for Un
11、derground Installation of Thermoplas-tic Pipe for Sewers and Other Gravity-Flow ApplicationsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Practice for Determination of the Impact Resistanceof Thermoplastic Pipe and Fittings by M
12、eans of a Tup(Falling Weight)D2990 Test Methods for Tensile,Compressive,and FlexuralCreep and Creep-Rupture of PlasticsD3212 Specification for Joints for Drain and Sewer PlasticPipes Using Flexible Elastomeric SealsD3895 Test Method for Oxidative-Induction Time of Poly-olefins by Differential Scanni
13、ng CalorimetryD4101 Classification System and Basis for Specification forPolypropylene Injection and Extrusion Materials1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.Current edition approv
14、ed April 1,2019.Published April 2019.Originallyapproved in 2011.Last previous edition approved in 2018 as F288118a.DOI:10.1520/F288119.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informa
15、tion,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance wi
16、th internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 D4218 Test Method for Determination of Carbon BlackContent in Polyethylene Compounds By the Muffle-Furnace TechniqueD4389/D4389M Specification for Finished Glass FabricsWoven From RovingsD6992 Test Method for Accelerated Tensile Creep andCree
