1、www.astm.orgISBN:978-0-8031-7514-3Stock#:STP1528JAI Guest EditorThomas S.WalshJAI Plastic Pipe and Fittings:Past,Present,and FutureSTP 1528WalshJournal of ASTM InternationalSelected Technical Papers STP 1528Plastic Pipe and FittingsPast,Present,and Future Journal of ASTM International Selected Techn
2、ical Papers STP1528Plastic Pipe and Fittings:Past,Present,and FutureJAI Guest Editor:Thomas S.WalshASTM International100 Barr Harbor DrivePO Box C700West Conshohocken,PA 19428-2959Printed in the U.S.A.ASTM Stock#:STP1528 Library of Congress Cataloging-in-Publication DataISSN:978-0-8031-7514-3Copyrig
3、ht 2011 ASTM INTERNATIONAL,West Conshohocken,PA.All rights reserved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,fi lm,or other distribution and storage media,without the written consent of the publisher.Journal of ASTM International(JAI)Scop
4、eThe JAI is a multi-disciplinary forum to serve the international scientifi c and engineering community through the timely publication of the results of original research and critical review articles in the physical and life sciences and engineering technologies.These peer-reviewed papers cover dive
5、rse topics relevant to the science and research that establish the foundation for standards development within ASTM International.Photocopy RightsAuthorization to photocopy items for internal,personal,or educational classroom use,or the internal,personal,or educational classroom use of specifi c cli
6、ents,is granted by ASTM International provided that the appropriate fee is paid to ASTM International,100 Barr Harbor Drive,P.O.Box C700,West Conshohocken,PA 19428-2959,Tel:610-832-9634;online:http:/www.astm.org/copyright.The Society is not responsible,as a body,for the statements and opinions expre
7、ssed in this publication.ASTM International does not endorse any products represented in this publication.Peer Review PolicyEach paper published in this volume was evaluated by two peer reviewers and at least one editor.The authors addressed all of the reviewers comments to the satisfaction of both
8、the technical editor(s)and the ASTM International Committee on Publications.The quality of the papers in this publication refl ects not only the obvious efforts of the au-thors and the technical editor(s),but also the work of the peer reviewers.In keeping with long-standing publication practices,AST
9、M International maintains the anonymity of the peer reviewers.The ASTM International Committee on Publications acknowledges with appreciation their dedication and contribution of time and effort on behalf of ASTM International.Citation of PapersWhen citing papers from this publication,the appropriat
10、e citation includes the paper authors,“paper title”,J.ASTM Intl.,volume and number,Paper doi,ASTM International,West Conshohocken,PA,Paper,year listed in the footnote of the paper.A citation is provided as a footnote on page one of each paper.Printed in Baltimore,MD November,2011 ForewordTHIS COMPIL
11、ATION OF THE JOURNAL OF ASTM INTERNATIONAL(JAI),STP1528,Plastic Pipe and Fittings:Past,Present,and Future contains only the papers published in JAI that were presented at a Symposium on Plastic Pipe and Fittings:Yesterday,Today,and Tomorrow held during November 9,2009 in Atlanta,GA,USA.The Symposium
12、 was sponsored by ASTM International Committee F17 on Plastic Piping Systems.Thomas S.Walsh,Walsh Consulting Services,Houston,TX served as the Symposium Chairman and JAI Guest Editor.ContentsOverview.viiHistorical ReviewsNorth Americas Cinderella Pipe Story:A Look at PVC Pipes Climb to the TopB.Walk
13、er.3A Brief History of the Introduction,Development and Growth of the Corrugated Polyethylene Pipe Industry in North AmericaJ.B.Goddard.20The Hydrostatic Stress Board of Plastics Pipe Institute:The First 50 YearsS.A.Mruk.35Long-Term Hydrostatic Strength and Design of Thermoplastic Piping CompoundsS.
14、Boros.56NSF 14:Shaping the Future of the Plastic Piping IndustryA.Ciechanowski.73ASTM D 3350:A Historical and Current Perspective on a Standard Specifi cation forIdentifi cation of Polyethylene Plastics Pipe and Fittings MaterialsW.G.Jee.82DesignA Service Life Assessment of Corrugated HDPE Drainage
15、PipeM.Pluimer.91Designing Stormwater Chambers to Meet AASHTO Specifi cationsT.J.McGrath and D.Mailhot.102Design and Performance of Plastic Drainage Pipes in Environmental Containment FacilitiesR.W.I.Brachman.113Design Development of Large Thermoplastic Chambers for StormWater RetentionB.J.Bass,T.J.M
16、cGrath,D.Mailhot,and K.-W.Lim.132Technical Considerations When Fabricating PVC Pressure FittingsT.Franzen,C.Fisher,and S.Rahman.150Defl ection Lag,Load Lag,and Time Lag of Buried Flexible PipeA.Howard.162Testing and Failure AnalysisStress Crack Protocol for Finished Product Testing of Corrugated High Density Polyethylene PipeJ.M.Kurdziel.173Guided Side-Bend:An Alternative Qualifi cation Method for Butt Fusion Joining ofPolyethylene Pipe and Fittings S.Sandstrum,D.Burwell,S.McGriff,J.Craig,and H.
