收藏 分享(赏)

ASTM_F_824_-_93_2010.pdf

上传人:益****师 文档编号:190088 上传时间:2023-03-04 格式:PDF 页数:7 大小:228.75KB
下载 相关 举报
ASTM_F_824_-_93_2010.pdf_第1页
第1页 / 共7页
ASTM_F_824_-_93_2010.pdf_第2页
第2页 / 共7页
ASTM_F_824_-_93_2010.pdf_第3页
第3页 / 共7页
ASTM_F_824_-_93_2010.pdf_第4页
第4页 / 共7页
ASTM_F_824_-_93_2010.pdf_第5页
第5页 / 共7页
ASTM_F_824_-_93_2010.pdf_第6页
第6页 / 共7页
亲,该文档总共7页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:F82493(Reapproved 2010)An American National StandardStandard Specification forTables,Mess,Marine,Steel1This standard is issued under the fixed designation F824;the number immediately following the designation indicates the year of originaladoption or,in the case of revision,the year of l

2、ast revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the construction of round,square,and rectangular marine mess tables with or withoutadjustable lee ra

3、ils for use in crew,officer,and passengerdining areas aboard ship.1.2 The values stated in inch-pound units are to be regardedas the standard.The metric equivalents,given in parentheses,are provided for information only.2.Referenced Documents2.1 ASTM Standards:2A53/A53M Specification for Pipe,Steel,

4、Black and Hot-Dipped,Zinc-Coated,Welded and SeamlessA167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate,Sheet,and Strip(With-drawn 2014)3A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and Strip for PressureVessels and for General Appl

5、icationsA366/A366M Specification for Commercial Steel(CS)Sheet,Carbon,(0.15 Maximum Percent)Cold-Rolled(Withdrawn 2000)3A500 Specification for Cold-Formed Welded and SeamlessCarbon Steel Structural Tubing in Rounds and ShapesA501 Specification for Hot-Formed Welded and SeamlessCarbon Steel Structura

6、l TubingA567/A567M Specification for Castings,Iron,Cobalt,andNickel-Base Alloy,for High Strength at Elevated Tem-peratures(Withdrawn 1987)3A582/A582M Specification for Free-Machining StainlessSteel BarsB221 Specification for Aluminum and Aluminum-Alloy Ex-truded Bars,Rods,Wire,Profiles,and TubesD907

7、 Terminology of Adhesives2.2 National Electrical Manufacturers Association:NEMA LD-3 High Pressure Decorative Laminates42.3 American Institute of Steel Construction Manual:AISC Wire and Sheet Metal Gages Equivalent Thicknessin Decimals of an Inch,U.S.Standard Gage(USSG)forUncoated Hot and Cold Rolle

8、d Sheets53.Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 mess tablea dining table for use in crew,officer,orpassenger dining areas,consisting of a horizontal top assemblyand one or more supporting pedestals.3.1.2 table topthe assembled horizontal surface of themess table includ

9、ing the substrate,top covering,lee rails,andedge binder,or all of the preceding.3.1.2.1 substratethe structural core of the top assembly.3.1.2.2 top coveringthe decorative melamine laminateattached to the top surface of the substratae.3.1.2.3 Lee Rails:(1)fixed lee raila trim piece at theedge of the

10、 table top that projects above the upper surface ofthe table top to retain tableware and act as an edge binder.(2)adjustable lee raila trim piece at the edge of the tabletop that can be raised above the upper surface of the table topto retain tableware and can be retracted when not needed.3.1.2.4 ed

11、ge binderthe finishing strips of metal applied tothe edge of the table top.3.1.2.5 cleanoutan interruption in the raised portion of thelee rail to facilitate cleaning of table top.3.1.2.6 pedestala round or square tubular column,orstanchion,that supports the table top.Each pedestal has atable-suppor

12、t plate at its upper end and provisions at the bottomfor attaching to the structural deck.(1)table support platea flanged,dished plate or flat platewith gussets welded to top of pedestal for supporting andattaching to the table top.3.1.2.7 deck socketa metal sleeve or adaptor welded to thestructural

13、 deck,over which the table pedestal is installed andattached.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved March 1,2010.Published April

14、 2010.Originallyapproved 1983.Last previous edition approved in 2004 as F824 93(2004).DOI:10.1520/F0824-93R10.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standar

15、ds Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from National Electrical Manufacturers Association(NEMA),1300N.17th St.,Suite 1752,Rosslyn,VA 22209,http:/www.nema.org.5Available from American Institute of Stee

16、l Construction(AISC),One E.Wacker Dr.,Suite 700,Chicago,IL 60601-2001,http:/www.aisc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 4.Classification4.1 Types:4.1.1 Type IRound mess table with single pedestal.4.1.2 Type IISquare mess table with single pedestal.4.1.3 Type IIIRectangular mess table.4.1.3.1Grade 1Rectangular table with single pedestal.4.1.3.2 Grade 2Rectangular table with two pedestals.4.2 Classes:4.2.1 Class ATable

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2