1、Designation:F94512(Reapproved 2019)Standard Test Method forStress-Corrosion of Titanium Alloys by Aircraft EngineCleaning Materials1This standard is issued under the fixed designation F945;the number immediately following the designation indicates the year of originaladoption or,in the case of revis
2、ion,the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.INTRODUCTIONChemical solutions and
3、compounds used for preinspection cleaning or for preservation of titaniumalloy aircraft turbine engine parts shall be subject to qualification requirements of this test method.1.Scope1.1 This test method establishes a test procedure for deter-mining the propensity of aircraft turbine engine cleaning
4、 andmaintenance materials for causing stress corrosion cracking oftitanium alloy parts.1.2 The evaluation is conducted on representative titaniumalloys by determining the effect of contact with cleaning andmaintenance materials on tendency of prestressed titaniumalloys to crack when subsequently hea
5、ted to elevated tempera-tures.1.3 Test conditions are based upon manufacturers maxi-mum recommended operating solution concentration.1.4 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for i
6、nformation onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicabil
7、ity of regulatory limitations prior to use.For specific precautionary statements,see 5.3 and 5.6.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International S
8、tandards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D740 Specification for Methyl Ethyl KetoneD841 Specification for Nitration Grade TolueneD1193 Specification for Reagent Water2.2 SAE Aerospac
9、e Material Specifications:3AMS 4911 Sheet,Strip and Plate-6AL-4V AnnealedAMS 4916 Sheet,Strip,and Plate-8AL 1MO 1V,DuplexAnnealed3.Significance and Use3.1 Because of the tendency of prestressed titanium alloyparts to crack if heated while in contact with certain chemicalreagents,it is necessary to e
10、nsure that cleaning and mainte-nance materials will not initiate stress corrosion of titaniumalloys under controlled conditions.For test specimens,twocommon titanium alloys are selected,one that is very suscep-tible(AMS 4916)and one that is not very susceptible(AMS4911)to stress corrosion cracking.4
11、.Apparatus4.1 Measuring Device capable of linear measurement with a60.01-in.(60.25-mm)tolerance.4.2 Press Forming Apparatus4with 0.56-in.(14-mm)diam-eter mandrel capable of producing approximately 65 bends in0.050-in.(1.25-mm)titanium alloy sheet specimens.1This test method is under the jurisdiction
12、 of ASTM Committee F07 onAerospace and Aircraft and is the direct responsibility of Subcommittee F07.07 onQualification Testing of Aircraft Cleaning Materials.Current edition approved May 1,2019.Published June 2019.Originallyapproved in 1985.Last previous edition approved in 2012 as F945 12.DOI:10.1
13、520/F0945-12R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Society of Automotive Engineers,40
14、0 Commonwealth Dr.,Warrendale,PA 15096.4The sole source of supply of the apparatus(A laboratory bench hydraulic pressENER PAC Model No.P-39 has been found satisfactory)known to the committeeat this time is Black Hawk Industrial Products,Butler,WI 53007.If you are awareof alternative suppliers,please
15、 provide this information to ASTM InternationalHeadquarters.Your comments will receive careful consideration at a meeting of theresponsible technical committee,1which you may attend.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis inter
16、national standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 4.3 Beakers or Small Tanks for containment of cleaning,rinsing,and test solutions,appropriately lined to preventcontamination of the solutions by container materials.4.4 Vise,capable of precise
