1、Designation:F193501(Reapproved 2011)An American National StandardStandard Test Method forMeasuring the Headroom of a Backpacking orMountaineering Tent1This standard is issued under the fixed designation F1935;the number immediately following the designation indicates the year oforiginal adoption or,
2、in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers tents for use in the sports ofbackpacking and mountaineering.It
3、 establishes requirementsfor the testing and marking of tents.1.2 This test method may contain test methods that do notentirely simulate real life situations.This test method isdesigned to give reproducible results in a laboratory andthereby a means for product comparison.1.3 This standard does not
4、purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Terminology2.1 Definitions of Terms Specifi
5、c to This Standard:2.1.1 tenta portable shelter made primarily of fabricweighing less than 3 oz/yd2,designed to be carried by theoccupants for while backpacking or mountaineering.2.1.2 usable headroomthe interior vertical measurementof a tent measured from the tent floor to the high point on theceil
6、ing using a simple fixture that simulates an average usershead.3.Summary of Test Method3.1 The tent should be pitched on a flat surface in accor-dance with the companys supplied pitching instructions.3.2 The fixture shall be placed inside the tent.The ball israised until it comes into contact with t
7、he ceiling,wall,poles,or any other obstructions inside the tent.3.3 The tape measure will now be hanging directly belowthe ball.The headroom measurement will be where themeasuring tape hits the tent floor.If the tent does not have afloor,record the measurement to the surface the tent has beenset up
8、on.4.Significance and Use4.1 This test method can be used to quantify and compareheadroom of backpacking and mountaineering tents.Themeasured headroom can be used as a manufacturing standardor a measurement that can be used by consumers to comparethe interior height of a variety of tents,or both.5.A
9、pparatus5.1 Specifications for Headroom Measurement Fixture(seeFig.1):5.1.1 Styrofoam ball 6 inches in diameter(mean width ofmale head=6.1 in.).25.1.2 Tape Measure,14in.GraduationsThe tape ismounted into the bottom of the Styrofoam ball,and the first 6inches are removed from the tape.In this way,the
10、 reading willbe simple and accurate.6.Conditioning6.1 Tests may be completed under ambient conditions.Incases of dispute,test samples shall be conditioned in accor-dance with 6.2.6.2 The tent samples are first erected and dried in anatmosphere with a relative humidity of less than 10%for aminimum pe
11、riod of 24 h.They are then placed in an atmo-sphere of 50 6 5%relative humidity,20 6 2 C for aminimum period of 72 h.Tests may then be done outside theconditioning room,but the temperature shall be 23 6 5 C andthe tests shall begin within 5 min.of removal from condition-ing and be completed within 4
12、 h.7.Sampling,Test Specimens,and Test Units7.1 The tent test specimen shall be new and in unusedcondition.When possible,it shall be selected randomly from aproduction lot of a given model of tent.It shall conform in allrespects to the manufacturers specifications for that model.8.Report8.1 The test
13、report shall include the name of the tentmanufacturer,the model of tent tested,the date and location of1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment and Facilitiesand is the direct responsibility of Subcommittee F08.22 onCamping Softgoods.Current edition approv
14、ed April 1,2011.Published June 2011.Originallyapproved in 1998.Last previous edition approved in 2007 as F1935 01(2007).DOI:10.1520/F1935-01R11.2Henry Dreyfuss Associates,The Measure of Man and Woman:Human Factorsin Design,Whitney Library of Design,1993.Copyright ASTM International,100 Barr Harbor D
15、rive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 the tests,the name(s)of personnel conducting the tests,if thetent is a production model or prototype,and the peak height.8.2 Markings,if included in the tent or marketing literature,shall reference this test method.9.Precision and Bias9
16、.1 The precision of this test method is within14in.Thebias of this test method has not yet been determined.10.Keywords10.1 backpacking;height;mountaineering;peak;tentsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.T
