收藏 分享(赏)

ASTM_F_3329_-_18.pdf

上传人:益****师 文档编号:190850 上传时间:2023-03-04 格式:PDF 页数:4 大小:92.94KB
下载 相关 举报
ASTM_F_3329_-_18.pdf_第1页
第1页 / 共4页
ASTM_F_3329_-_18.pdf_第2页
第2页 / 共4页
ASTM_F_3329_-_18.pdf_第3页
第3页 / 共4页
ASTM_F_3329_-_18.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F332918Standard Specification forCarbon and Alloy Steel Metric Rivets1This standard is issued under the fixed designation F3329;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenth

2、eses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers chemical and mechanical re-quirements for nine property classes of carbon and alloy steelmetric rivets in nominal diameters M01 th

3、rough M36 suited foruse in general engineering applications.1.2 This specification does not cover dimensional require-ments for rivets of any property class.When referencing thisspecification for procurement purposes,it is mandatory thatsize,type,style,and any special dimensions of the product beadd

4、itionally specified.1.2.1 In case of any conflict in requirements,the require-ments of the individual product specification shall take prece-dence over those of this general specification.1.2.2 The purchaser may specify additional requirementswhich do not negate any of the provisions of this general

5、specification or of the individual product specification.Suchadditional requirements,the acceptance of which are subject tonegotiation with the supplier,must be included in the orderinformation(see Section 3).1.3 When agreed on by the purchaser,Class 5.8 fastenersmay be supplied when either Classes

6、4.6 or 4.8 are ordered;Class 4.8 may be supplied when Class 4.6 is ordered;1.4 The product size range for which each property class isapplicable is given in Table 1 on chemical compositionrequirements,and the mechanical requirements table(seeTable 2).1.5 Appendix X1 explains the significance of the

7、propertyclass designation numerals.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade

8、 Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A153/A153M Specification for Zinc Coating(Hot-Dip)onIron and Steel HardwareA588/A588M Specification for High-Strength Low-AlloyStructural Steel,up to 50 ksi 345 MPa Minimum YieldPoint,with Atmospheric Co

9、rrosion ResistanceA751 Test Methods,Practices,and Terminology for Chemi-cal Analysis of Steel ProductsB695 Specification for Coatings of Zinc Mechanically De-posited on Iron and SteelF606/F606M Test Methods for Determining the MechanicalPropertiesofExternallyandInternally ThreadedFasteners,Washers,D

10、irect Tension Indicators,and RivetsF788/F788M Specification for Surface Discontinuities ofBolts,Screws,and Studs,Inch and Metric SeriesF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection3.Ordering Information3.1 Orders for products referencing this sp

11、ecification shallinclude the following:3.1.1 Quantity(number of pieces),3.1.2 Name of product rivet,3.1.3Dimensions,including nominal diameter,and length(see Section 7),3.1.4 Property class,3.1.5Zinc CoatingSpecify the zinc coating processrequired,for example,hot dip,mechanically deposited,or nopref

12、erence(see 4.4),3.1.6 Other FinishesSpecify other protective finish,ifrequired,3.1.7 ASTM designation and year of issue,and3.1.8 Any special.3.1.9 Test reports if required,see Section 14.4.Materials and Manufacture4.1 Steel for rivets shall be made by the open-hearth,basic-oxygen,or electric-furnace

13、 process.1This test method is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts,Nuts,Rivets and Washers.Current edition approved Nov.15,2018.Published January 2019.DOI:10.1520/F3329-182For referenced ASTM standards,visit t

14、he ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United St

15、atesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Tr

16、ade(TBT)Committee.1 4.2 Heading Practice:4.2.1 Methods other than upsetting or extrusion,or both,arepermitted only by special agreement between purchaser andproducer.4.3Heat Treatment:4.3.1 Class 3.6,4.6,4.8,5.6 and 5.8 rivets need not be heattreated.4.3.2 Classes 4.8,5.6 and 5.8 rivets shall be stress relievedif necessary to assure the soundness of the head to shankjunction.When stress relieving is specified by the purchaser,Class 5.8 rivets shall be stress relieved at a minimum stress-relief t

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2