1、Designation:F310115Standard Specification forUnsupervised Public Use Outdoor Fitness Equipment1This standard is issued under the fixed designation F3101;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.INTRODUCTIONThe goal of this specification is to promote proper design,manufacturing,installation,andoperational practices for unsupervised outdoor fitnes
3、s equipment for use in parks,schools,institutions,multiple-family dwellings,private resorts,recreation developments and other areas.These productsare intended to be used by individuals age 13 and older and typically are used in an unsupervisedsetting.Through these specifications,this specification a
4、ims to assist designers,manufactures,andowner/operators in reducing the possibility of injury.Adult anthropometrics are used in the design of this equipment.The equipment specifications setforth in this standard are for equipment intended for use by individuals 13 and older.Adults must takeprecautio
5、ns and prevent children under their supervision from accessing and using this equipment.This standard specifies requirements that are generally applicable to all outdoor fitness equipment usedin an unsupervised setting.The equipment user must recognize,however,that a standard alone will not necessar
6、ily preventinjuries.Like other physical activities,exercise involving outdoor fitness equipment,involves the riskof injury,particularly if the equipment is used improperly,not properly installed or not properlymaintained.In addition,users with physical limitations should be aware of their capabiliti
7、es andlimitations in the use of this type of equipment and seek appropriate advice prior to using it.Certainphysical conditions or limitations may preclude some persons from using this equipment properly andwithout increasing the risk of serious injury.While the designer,manufacturer,and owner canno
8、tcontrol the public use of this unsupervised equipment they can address known causes of injuries to themost vulnerable users and unintended users-at-risk defined as those under the age of 13.Good designand best practice would dictate that these facilities are not in physical proximity or physicallys
9、eparated from playground for children because of hazardous conditions children cannot appreciate.1.Scope1.1 This specification establishes parameters for the designand manufacture of outdoor fitness equipment as defined in3.1.30.1.2 It is intended that these fitness products will be used inan unsupe
10、rvised outdoor setting or environment and will bepermanently anchored.1.2.1 It is the intent of this specification to only specifyrequirements for outdoor fitness equipment and its installationand not the design of the facility or grounds on which theproducts are to be installed.1.3 The specificatio
11、ns set forth in this standard are intendedto minimize the likelihood of serious injuries.1.3.1 The specifications set forth in this standard are foroutdoor fitness equipment intended for use in an unsupervisedsetting by individuals age 13 and older.1.4 The values stated in SI(metric)units are to be
12、regardedas standard.The values in parentheses are for information only.1.5 General Measures,Tolerances,and Conversions:1.5.1 The general tolerances for this specification(unlessotherwise specified)are as follows:DimensionToleranceX mm(X in.)13.0 mm(0.5 in.)X.X mm(X.X in.)1.3 mm(0.05 in.)X.XX mm(X.XX
13、 in.).0.130 mm(0.005 in.)1.5.2 These tolerances still apply to a dimension even whenterms like greater than,less than,minimum,or maximum areused.1This specification is under the jurisdiction of ASTM Committee F08 on SportsEquipment,Playing Surfaces,and Facilities and is the direct responsibility ofS
14、ubcommittee F08.30 on Fitness Products.Current edition approved April 1,2015.Published May 2015.DOI:10.1520/F3101-15.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 1.6 This standard is to be used in conjunction with TestMethods F2571 and
15、 Specification F2276.If a design orinstallation concern is not addressed in this specification thenthe applicable requirements of Specification F2276 shall beused.1.6.1 This standard takes precedence over SpecificationF2276 and Test Methods F2571 in areas that are addressed inthis document.1.7 This
16、standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2F1077 Guide for Selection of Committee F16 FastenerSpecifications(Withdrawn 2014)3F1292 Specification for Impact Attenuation of SurfacingMaterials Within the Use Zone of Playground Equi
