1、STP 1131(Volume II)Fracture Mechanics:Twenty-Second Symposium(Volume II)S.N.Atluri,J.C.Newman,Jr.,I.S.Raju,and J.S.Epstein,editors ASTM Publication Code Number(PCN)04-011310-30 As M 1916 Race Street Philadelphia,PA 19103 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 18:55:23 EST 2015Downloa
2、ded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.ASTM Publication Code No.(PCN):04-011310-30 ISBN:0-8031-1440-0 ISSN:1040-3094 Copyright?9 1992 AMERICAN SOCIETY FOR TESTING AND MATERIALS,Phil-adelphia,PA.All rights rese
3、rved.This material may not be reproduced or copied,in whole or in part,in any printed,mechanical,electronic,film,or other distribution and storage media,without the written consent of the publisher.Photocopy Rights Authorization to photocopy items for internal or personal use,or the internal or pers
4、onal use of specific clients,is granted by the AMERICAN SOCIETY FOR TESTING AND MATERIALS for users registered with the Copyright Clearance Center(CCC)Transac-tional Reporting Service,provided that the base fee of$2.50 per copy,plus$0.50 per page is paid directly to CCC,27 Congress St.,Salem,MA 0197
5、0;(508)744-3350.For those organizations that have been granted a photocopy license by CCC,a separate system of payment has been arranged.The fee code for users of the Transactional Reporting Service is 0-8031-1440-0/92$2.50+.50.Peer Review Policy Each paper published in this volume was evaluated by
6、three peer reviewers.The authors addressed all of the reviewers comments to the satisfaction of both the technical editor(s)and the ASTM Committee on Publications.The quality of the papers in this publication reflects not only the obvious efforts of the authors and the technical editor(s),but also t
7、he work of these peer reviewers.The ASTM Committee on Publications acknowledges with appreciation their dedication and contribution to time and effort on behalf of ASTM.Printed in Baltimore,MD April 1992 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 18:55:23 EST 2015Downloaded/printed byUni
8、versity of Washington(University of Washington)pursuant to License Agreement.No further reproductions authorized.Foreword The Twenty-Second National Symposium on Fracture Mechanics was held on 26-28 June 1990 in Atlanta,Georgia.ASTM Committee E24 on Fracture Testing was the sponsor.The Executive Org
9、anizing Committee responsible for the organization of the meeting was com-posed of H.A.Ernst,Georgia Institute of Technology,who served as the symposium chairman,and the following vice-chairman:S.D.Antolovich,Georgia Institute of Tech-nology;S.N.Atluri,Georgia Institute of Technology;J.S.Epstein,Ida
10、ho National En-gineering Laboratory;D.L.McDowell,Georgia Institute of Technology;J.C.Newman,Jr.,NASA Langley Research Center;I.S.Raju,North Carolina State A&T University;and A.Saxena,Georgia Institute of Technology.The proceedings have been divided into two volumes.H.A.Ernst,A.Saxena,and D.L.McDowel
11、l served as editors of Volume I and S.N.Atluri,J.C.Newman,Jr.,I.S.Raju,and J.S.Epstein served as editors of Volume II.Copyright by ASTM Intl(all rights reserved);Wed Dec 23 18:55:23 EST 2015Downloaded/printed byUniversity of Washington(University of Washington)pursuant to License Agreement.No furthe
12、r reproductions authorized.Contents Introduction ELASTIC FRACTURE MECHANICS AND APPLICATIONS Experimental Determination of Fracture Parameters in Three-Dimensional Problems-c.w.SMITtt Crack-Mouth Displacements for Semelliptical Surface Cracks Subjected to Remote Tension and Bending Loads-I.s.RAJU,J.
13、C.NEWMAN,JR.,AND S.N.ATLURI Stress-Intensity Factors for Long Axial Outer Surface Cracks in Large R/T Pipes-R.B.STONESIFER,F.W.BRUST,AND B.N.LEIS An Inverse Method for the Calculation of Through-Thickness Fatigue Crack Closure Behavior-D.s.DAWlCKE,K.N.SHIVAKUMAR,J.C.NEWMAN,JR.,AND A.F.GRANDT,JR.ASTM
14、 E 1304,The New Standard Test for Plane-Strain(Chevron-Notched)Fracture Toughness:Usage of Test Results-L.M.BARKER Comparison of Mixed-Mode Stress-Intensity Factors Obtained Through Displacement Correlation,J-Integral Formulation,and Modified Crack-Closure Integral-T.N.BITTENCOURT,A.BARRY,AND A.R.IN
15、GRAFFEA Application of the Weight-Functions Method to Three-Dimensional Cracks Under General Stress Gradients-s.N.MALIK The Application of Line Spring Fracture Mechanics Methods to the Design of Complex Welded Structures-D.RITCHIE,C.W.M.VOERMANS,M.BELL,AND J.DELANGE NONLINEAR FRACTURE MECHANICS AND
16、APPLICATIONS Crack-Tip Displacement Fields and JR-Curves of Four Aluminum Alloys-M.S.DADKHAH,A.S.KOBAYASHI,AND W.L.MORRIS Application of the Hybrid Finite Element Method to Aircraft Repairs-P.TONG,R.GREIF,AND LI CHEN A Hybrid Numerical-Experimental Method for Caustic Measurements of the T*-Integral-T.NISHIOKA,T.EUJIMOTO,AND K.SAKAKURA 19 29 46 58 69 83 113 135 154 170 Copyright by ASTM Intl(all rights reserved);Wed Dec 23 18:55:23 EST 2015Downloaded/printed byUniversity of Washington(University
