1、 IEC 62153-4-10Edition 1.0 2009-05INTERNATIONAL STANDARD Metallic communication cable test methods Part 4-10:Electromagnetic compatibility(EMC)Shielded screening attenuation test method for measuring the screening effectiveness of feed-throughs and electromagnetic gaskets double coaxial method IEC 6
2、2153-4-10:2009(E)LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC,Geneva,Switzerland All rights reserved.Unless otherwise specified,no part of this publication may be reproduced
3、 or utilized in any form or by any means,electronic or mechanical,including photocopying and microfilm,without permission in writing from either IEC or IECs member National Committee in the country of the requester.If you have any questions about IEC copyright or have an enquiry about obtaining addi
4、tional rights to this publication,please contact the address below or your local IEC member National Committee for further information.IEC Central Office 3,rue de Varemb CH-1211 Geneva 20 Switzerland Email:inmailiec.ch Web:www.iec.ch About the IEC The International Electrotechnical Commission(IEC)is
5、 the leading global organization that prepares and publishes International Standards for all electrical,electronic and related technologies.About IEC publications The technical content of IEC publications is kept under constant review by the IEC.Please make sure that you have the latest edition,a co
6、rrigenda or an amendment might have been published.?Catalogue of IEC publications:www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria(reference number,text,technical committee,).It also gives information on projects,withdrawn and replaced publications.?IEC J
7、ust Published:www.iec.ch/online_news/justpub Stay up to date on all new IEC publications.Just Published details twice a month all new publications released.Available on-line and also by email.?Electropedia:www.electropedia.org The worlds leading online dictionary of electronic and electrical terms c
8、ontaining more than 20 000 terms and definitions in English and French,with equivalent terms in additional languages.Also known as the International Electrotechnical Vocabulary online.?Customer Service Centre:www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or ne
9、ed further assistance,please visit the Customer Service Centre FAQ or contact us:Email:csciec.ch Tel.:+41 22 919 02 11 Fax:+41 22 919 03 00 LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.IEC 62153-4-10Edition 1.0 2009-05INTERNATIONAL
10、STANDARD Metallic communication cable test methods Part 4-10:Electromagnetic compatibility(EMC)Shielded screening attenuation test method for measuring the screening effectiveness of feed-throughs and electromagnetic gaskets double coaxial method INTERNATIONAL ELECTROTECHNICAL COMMISSION SICS 33.120
11、.10;33.100 PRICE CODEISBN 2-8318-1039-4 Registered trademark of the International Electrotechnical Commission LICENSED TO MECON Limited.-RANCHI/BANGALOREFOR INTERNAL USE AT THIS LOCATION ONLY,SUPPLIED BY BOOK SUPPLY BUREAU.2 62153-4-10 IEC:2009(E)CONTENTS FOREWORD.3 1 Scope.5 2 Normative references.
12、5 3 Terms and definitions.5 4 Principle of the test method.8 5 Procedure.10 5.1 Equipment.10 5.2 Dynamic range.11 5.3 Sample preparation.11 6 Measurement.11 6.1 General.11 6.2 Screening attenuation.11 6.3 Transfer impedance.11 7 Expression of results.11 7.1 Transfer impedance.11 7.2 Screening attenu
13、ation.12 7.3 Requirements.12 Annex A(informative)Background for the measurement of the shielding effectiveness of feed-throughs and electromagnetic gaskets.13 Bibliography.22 Figure 1 A two-port.6 Figure 2 Equivalent circuit of the test set-up and definition of ZT.7 Figure 3 Cross-section of a typic
14、al feed-through configuration.9 Figure 4 Cross-section of the test fixture with a connector.9 Figure 5 Cross-section of the test fixture with an electromagnetic gasket.10 Figure A.1 Cross-section of a typical feed-through configuration.13 Figure A.2 Cross-section of the test fixture with a connector
15、.14 Figure A.3 Equivalent circuit of the test setup with the shunt admittance y of the feed-through.14 Figure A.4 TDR step response at input-port of test fixture.16 Figure A.5 View of the test fixture connected to a network analyzer.17 Figure A.6 Top view of the test fixture.17 Figure A.7 Detailed v
16、iew of the contact area.17 Figure A.8 Detailed view of the captivation for the conductive O-ring test.18 Figure A.9 Isolation of the network analyzer.19 Figure A.10 Isolation of the test fixture when characterizing an ideal short(metal plate).19 Figure A.11 Measured operational screening transmission when characterizing a typical conductive O-ring.20 Figure A.12 Transfer impedance ZT of a typical conductive O-ring.20 Figure A.13 Screening attenuation as of a typical conductive O-ring.21 LICENSED
