压缩包目录
-
全部
- iec61000-4-37-tr{ed1.0}support.xlsx--点击预览
- iec61000-4-37-tr{ed1.0}user guide.docx--点击预览
- iec61000-4-37{ed1.0}en.pdf--点击预览
文件预览区
|
|
资源描述
IEC TR 61000-4-37 SUPPORT SPREADSHEET USER GUIDE Page 1 of 9USER GUIDE FOR IEC TR 61000-4-37 SUPPORT SPREADSHEETForewordThis user guide provides instructions how to use the support spreadsheet that is made available as an essential supplement with IEC TR 61000-4-37.The IEC and the spreadsheet author disclaim liability for any personal injury,property or any other damages of any nature whatsoever,whether special,indirect,consequential or compensatory,directly or indirectly resulting from this software and the document upon which its methods are based,use of,or reliance upon.The spreadsheet and this user guide are provided free of charge,and free of copyrights.The spreadsheet is created using Microsoft Office,but can be opened and the calculations can be processed using other spreadsheet programs.The spreadsheet has only been tested under Windows-7 and Windows-8,but should also function correctly in the Android operating system.Mathieu van den Bergh is assigned within IEC/SC77A/WG-1 as the person to support the spreadsheet and this user guide.If new versions of the support spreadsheet or this user guide are made available in the future,they can be downloaded from Mathieu van den BerghJuly IEC TR 61000-4-37 SUPPORT SPREADSHEET USER GUIDE Page 2 of 9Functions of the support spreadsheetIntroductionThe IEC TR 61000-4-37 technical report specifies a method to generate known power parameters and current harmonics,using a set of resistive linear and phase controlled loads that are controlled via power electronic circuits.In essence,the current flow through the controlled resistive loads is turned“on”and“off”at user defined phase angles.Through power calculations and Fourier analysis,one can calculate all parameters with very high precision,provided the load values,the current conduction angles,and the applied voltage are known.The load values may vary slightly,due to component tolerances.Also,the power source used in harmonic emission test systems may have small variations in voltage,or the system may be utilized at nominal 220 Volt instead of nominal 230 Volt.Therefore,the spreadsheet allows for resistive load values,the start/stop phase angles at which the current flow is turned“on”and“off”,and the applied voltage to be specified.These parameters are then used to compute what the“ideal”power parameters for the selected setting should be.Thus,the user enters the values for linear load,controlled load,system voltage,and the start/stop phase angles in degrees,and the spreadsheet produces the“Calculated parameters”in cells F10 through F19,as well as the current harmonics in cells M2 M41.In addition,the spreadsheet computes the permitted tolerances for harmonics,per the specified methods in the technical report.Also,the spreadsheet has individual sheets for each of the test classes in IEC 61000-3-2.In these individual sheets the“ideal”harmonic levels are compared against the limits for the specific test class,and the percentage of limits is indicated,as well as the PASS/FAIL status for each harmonic order.Thus,the individual test class sheets allow the user to quickly compare the results of a harmonic emission test system measurement with the“ideal”values.The following pages show several examples how to enter and evaluate the values for some of the tests that are specified in IEC TR 61000-4-37.IEC TR 61000-4-37 SUPPORT SPREADSHEET USER GUIDE Page 3 of 9Entering the values for test 1 of IEC TR 61000-4-37 Test no.1 of IEC TR 61000-4-37 calls for a controlled load value of 80 that is turned“On”at 45 degrees and turned“Off”at 135 degrees.The linear load is not used in this test and therefore its value is set to 100,000 or 200,000.As follows from figure A-1 in Annex A of the technical report,the linear loads can be turned“on”or“off”individually,with power electronic devices.These devices usually have some very small leakage,which may be 1 2 mA.The 100,000 or 200,000 at a system voltage of 230 Volt result in allowing for a leakage current of 1.2 2.3 mA.Experience has shown that 1-2 mA is a pragmatic value,and 1-2 mA obviously has less than 0.1%effect on the overall current level,while not affecting the harmonics at all.The main sheet called“3-2”allows the user to enter specific values,while the sheet called“Class-A”provides details for the specific test class.Since Test-1 of the technical report is a“Class-A PASS”test,the user can select this“Class-A”sheet to see the harmonic percentages and the PASS/FAIL status.The figure below illustrates the values that are calculated for the specified load levels,and start/stop phase angles.The spreadsheet also computes the THC-I and POHC levels.The calculation below shows the harmonics for settings of exactly 230.0 Volt and 80.0.“Class-A Pass”test values per Test no.1 of IEC TR 61000-4-37IEC TR 61000-4-37 SUPPORT SPREADSHEET USER GUIDE Page 4 of 9Example for test 1 with minor changes in voltage and load If the system voltage deviates a little,and perhaps the load is not exactly 80,the u
展开阅读全文
相关搜索