1、Packaged,Integrally GearedCentrifugal Air Compressors forPetroleum,Chemical,and GasIndustry ServicesAPI STANDARD 672FOURTH EDITION,MARCH 2004ERRATA,OCTOBER 2007ERRATA 2.JULY 2010energ):1SPECIAL NOTESAPI publications necessarily address problems of a general nature.With respect to partic-ular circums
2、tances,local,state,and federal laws and regulations should be reviewed.API is not undertaking to meet the duties of employers,manufacturers,or suppliers towarn and properly train and equip their employees,and others exposed,concerning healthand safety risks and precautions,nor undertaking their obli
3、gations under local,state,or fed-eral laws.Information concerning safety and health risks and proper precautions with respect to par-ticular materials and conditions should be obtained from the employer,the manufacturer orsupplier of that material,or the material safety data sheet.Nothing contained
4、in any API publication is to be construed as granting any right,byimplication or otherwise,for the manufacture,sale,or use of any method,apparatus,or prod-uct covered by letters patent.Neither should anything contained in the publication be con-strued as insuring anyone against liability for infring
5、ement of letters patent.Generally,API standards are reviewed and revised,reaffirmed,or withdrawn at leastevery five years.Sometimes a one-time extension of up to two years will be added to thisreview cycle.This publication will no longer be in effect five years after its publication dateas an operat
6、ive API standard or,where an extension has been granted,upon republication.Status of the publication can be ascertained from the API Standards department telephone(202)682-8000.A catalog of API publications,programs and services is published annuallyand updated biannually by API,and available throug
7、h Global Engineering Documents,15Inverness Way East,M/S C303B,Englewood,CO 80112-5776.This document was produced under API standardization procedures that ensure appropri-ate notification and participation in the developmental process and is designated as an APIstandard.Questions concerning the inte
8、rpretation of the content of this standard or com-ments and questions concerning the procedures under which this standard was developedshould be directed in writing to the Director of the Standards department,American Petro-leum Institute,1220 L Street,N.W.,Washington,D.C.20005.Requests for permissi
9、on toreproduce or translate all or any part of the material published herein should be addressed tothe Director.Business Services.API standards are published to facilitate the broad availability of proven,sound engineer-ing and operating practices.These standards are not intended to obviate the need
10、 for apply-ing sound engineering judgment regarding when and where these standards should beutilized.The formulation and publication of API standards is not intended in any way toinhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the mar
11、kingrequirements of an API standard is solely responsible for complying with all the applicablerequirements of that standard.API does not represent,warrant,or guarantee that such prod-ucts do in fact conform to the applicable API standard.All rights reserved.No part of this work may be reproduced,st
12、ored in a retrieval system,ortransmitted by any means,electronic,mechanical,photocopying,recording,or otherwise,without prior written permission from the publisher.Contact the Publisher;APl PublishingServices,1220 L Street,N.W.,Washington,D.C.20005.Copyright 2004.2007 American Petroleum InstituteFOR
13、EWORDAPI publications may be used by anyone desiring to do so.Every effort has been made bythe Institute to assure the accuracy and reliability of the data contained in them;however,theInstitute makes no representation,warranty,or guarantee in connection with this publicationand hereby expressly dis
14、claims any liability or responsibility for loss or damage resultingfrom its use or for the violation of any federal,state,or municipal regulation with which thispublication may conflict.Suggested revisions are invited and should be submitted to APl,Standards department,1220 L Street,NW,Washington,DC 20005.
