1、In-service Inspection of Mooring Hardware for Floating StructuresAPI RECOMMENDED PRACTICE 2I THIRD EDITION,APRIL 2008REAFFIRMED,SEPTEMBER 2020In-service Inspection of Mooring Hardware for Floating StructuresUpstream SegmentAPI RECOMMENDED PRACTICE 2I THIRD EDITION,APRIL 2008 REAFFIRMED,SEPTEMBER 202
2、0Special NotesAPI publications necessarily address problems of a general nature.With respect to particular circumstances,local,state,and federal laws and regulations should be reviewed.Neither API nor any of APIs employees,subcontractors,consultants,committees,or other assignees make anywarranty or
3、representation,either express or implied,with respect to the accuracy,completeness,or usefulness ofthe information contained herein,or assume any liability or responsibility for any use,or the results of such use,of anyinformation or process disclosed in this publication.Neither API nor any of APIs
4、employees,subcontractors,consultants,or other assignees represent that use of this publication would not infringe upon privately owned rights.API publications may be used by anyone desiring to do so.Every effort has been made by the Institute to assure theaccuracy and reliability of the data contain
5、ed in them;however,the Institute makes no representation,warranty,orguarantee in connection with this publication and hereby expressly disclaims any liability or responsibility for loss ordamage resulting from its use or for the violation of any authorities having jurisdiction with which this public
6、ation mayconflict.API publications are published to facilitate the broad availability of proven,sound engineering and operatingpractices.These publications are not intended to obviate the need for applying sound engineering judgmentregarding when and where these publications should be utilized.The f
7、ormulation and publication of API publicationsis not intended in any way to inhibit anyone from using any other practices.Any manufacturer marking equipment or materials in conformance with the marking requirements of an API standardis solely responsible for complying with all the applicable require
8、ments of that standard.API does not represent,warrant,or guarantee that such products do in fact conform to the applicable API standard.All rights reserved.No part of this work may be reproduced,stored in a retrieval system,or transmitted by any means,electronic,mechanical,photocopying,recording,or
9、otherwise,without prior written permission from the publisher.Contact the Publisher,API Publishing Services,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Copyright 2008 American Petroleum InstituteForewordThis recommended practice is under the jurisdiction of the API Subcommittee on Off
10、shore Structures.Nothing contained in any API publication is to be construed as granting any right,by implication or otherwise,for themanufacture,sale,or use of any method,apparatus,or product covered by letters patent.Neither should anythingcontained in the publication be construed as insuring anyo
11、ne against liability for infringement of letters patent.This document was produced under API standardization procedures that ensure appropriate notification and participation in the developmental process and is designated as an API standard.Questions concerning the interpretation of the content of t
12、his publication or comments and questions concerning the procedures under which this publication was developed should be directed in writing to the Director of Standards,American Petroleum Institute,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Requests for permission to reproduce or tr
13、anslate all or any part of the material published herein should also be addressed to the director.Generally,API standards are reviewed and revised,reaffirmed,or withdrawn at least every five years.A one-time extension of up to two years may be added to this review cycle.Status of the publication can
14、 be ascertained from the API Standards Department,telephone(202)682-8000.A catalog of API publications and materials is published annually and updated quarterly by API,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001.Suggested revisions are invited and should be submitted to the Standards
15、Department,API,200 Massachusetts Avenue,NW,Suite 1100,Washington,DC 20001,standardsapi.org.iiiContentsPage1Scope.11.1General.11.2Purpose.11.3Inspection Philosophy and Exception to This Document.11.4Mooring Component Traceability and Inspection Documentation.22Guidelines for In-service Inspection of
16、MODU Mooring Chain and Anchor Jewelry.22.1Common Problems with MODU Chain.22.2Recommended Inspection Method.32.3Recommended Inspection Procedure .72.4Guidelines for Rejecting Chain Components.122.5Guidelines for Chain Repair,Removal,and Replacement.142.6Recommended Inspection Schedule.152.7Special Event Inspection .163Guidelines for In-service Inspection of MODU Mooring-wire Rope and Anchor Handling Equipment .163.1Common Problems with MODU Mooring-wire Rope.163.2Recommended Inspection Method.23