1、AN AMERICAN NATIONAL STANDARD T-Slots,Their Bolts,Nuts,andTongues ANSI/ASME B5JM-1985(REVISION OF ANSI B5.1-197 5)SPONSORED AND PUBLHED BY THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS United Engineering Center 345 East 47th Street New York,N.Y.10017 REAFFIRMED 2014FOR CURRENT COMMITTEE PERSONNELPLEA
2、SE E-MAIL CSasme.orgDate of Issuance:September 15,1986 This Standard will be revised when the Society approves the issuance of a new edition.There will be no addenda or written interpretations of the requirements of this Standard issued to this Edition.This code or standard was developed under proce
3、dures accredited as meeting the criteria for American National Standards.The Consensus Committee that approved the code or standard was balanced to assure that individuals from competent and concerned interests have had an oppor tunity to participate.The proposed code or standard was made available
4、for public review and comment which provides an opportunity for additional public input from industry,academia,reg ulatory agencies,and the public-at-large.ASME does not approve,rate,or endorse any item,construction,proprietary device,or activity.ASME does not take any position with respect to the v
5、alidity of any patent rights asserted in connection with any items mentioned in this document,and does not undertake to insure anyone utilizing a standard against liability for infringement of any applicable Letters Patent,nor assume any such liability.Users of a code or standard are expressly advis
6、ed that determination of the validity of any such patent rights,and the risk of infringement of such rights,is entirely their own responsibility.Participation by federal agency representative(s)or person(s)affiliated with industry is not to be interpreted as government or industry endorsement of thi
7、s code or standard.ASME accepts responsibility for only those interpretations issued in accordance with governing ASME procedures and policies which preclude the issuance of interpretations by individual vol unteers.No part of this document may be reproduced in any form,in an electronic retrieval sy
8、stem or otherwise,without the prior written permission of the publisher.Copyright 1986 by THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS All Rights Reserved Printed in U.S.A.FOREWORD(This Foreword is not part of ANSI/ASME B5.1 M-1985.)Work on the standardization of T-slots started in 1924 and a tentat
9、ive standard was published in 1927.The first official American Standard for T-slots came in 1941.This was last revised in 1949.The 1975 revision continued the basic sizes originally established.However,all.dimensions except the nominal T-bolt size were converted to decimal inches in recognition of t
10、he increasing preference of industry for decimals.Much material that was originally included to cover the transitional period has been deleted.A lettering system for the figures has been adopted that should facilitate cross reference between tables.In this system,comparable dimensions bear the same
11、letter with a subscript indicating table number.Thus,A1 is width of T-slot throat,A2 is diameter of T-bolt to fit that throat,and A3 is width of T-nut tongue to fit that throat.Metric T-slots,as they have been standardized by ISO/TC39,Machine Tools,have been placed side by side with the inch-sized T
12、-slots.Interchangeability is possible between corresponding sizes of the two measuring systems with the exception of the locating tongue and T-slot throat dimensions,and the difference in the fastening threads on T-bolts.The listing of T-slots and T-bolts in ISO 299-1973,although essentially identic
13、al to sizes listed in this Standard,are rejected because they are shown with fractional dimensions.The spacing of T-slotsin machine tool components as given in ISO 299-1973 is likewise rejected following consensusof U.S.builders and users of machine tools.This Standard accepts the tolerance codes of
14、 ISO286 for metric sizes of T-slots only.Information relative to cutters for T-slots has been deleted to avoid duplication and possible conflict with information contained in ANSI/ASME B94.19,Milling Cutters and End Mills.Following approval by the Standards Committee,the 1975 revision was presented
15、to the sponsor organizations and to ANSI for approval and designation as an American National Standard.This was granted on August 8,1975.The 1985 revision was approved as an American National Standard on December 12,1985.iii Intentionally left blank ASME STANDARDS COMMITTEE B5 Machine Tools,Componen
16、ts,Elements,Performance,and Equipment(The following is the roster of the Committee at the time of approval of this Standard).OFFICERS R.T.Woythal.Vice Chairman,Group A W.S.Roorda,Vice Chairman,Group B H.Cooper.Vice Chairman,Group C W.R.Daisak,Secretary COMMITTEE PERSONNEL THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS F.S.Blackall,The Taft-Pierce Manufacturing Co.,Woonsocket,Rhode Island DEFENSE INDUSTRIAL PLANT EQUIPMENT CENTER J.W.Lynch.Defense Logistics Agency,Memphis,Tennessee D.Williams.Alter
