1、AN AMERICAN NATIONAL STANDARDASME B5.60b-2009ADDENDAtoASME B5.60-2002WORKHOLDING CHUCKS:JAW TYPE CHUCKSIncorporating ASME B5.60.1,ASME B5.60.3,ASME B5.60.4,and ASME B5.60.5THE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park Avenue O New York,NY 10016M0184BCopyright 2009 by the American Society of
2、 Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled whe
3、n printed.Date of Issuance:November 10,2009ASME is the registered trademark of The American Society of Mechanical Engineers.This code or standard was developed under procedures accredited as meeting the criteria forAmerican National Standards.The Standards Committee that approved the code or standar
4、dwas balanced to assure that individuals from competent and concerned interests have had anopportunity to participate.The proposed code or standard was made available for public reviewand comment that provides an opportunity for additional public input from industry,academia,regulatory agencies,and
5、the public-at-large.ASME does not“approve,”“rate,”or“endorse”any item,construction,proprietary device,or activity.ASME does not take any position with respect to the validity of any patent rights asserted inconnection withany itemsmentioned inthis document,and doesnot undertaketo insureanyoneutilizi
6、ng a standardagainst liability for infringementof any applicable letterspatent,nor assumesany such liability.Users of a code or standard are expressly advised that determination of thevalidity of any such patent rights,and the risk of infringement of such rights,is entirely theirown responsibility.P
7、articipation by federal agency representative(s)or person(s)affiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibility for only those interpretations of this document issued inaccordance with the established ASME proced
8、ures and policies,which precludes the issuanceof interpretations by individuals.No part of this document may be reproduced in any form,in an electronic retrieval system or otherwise,without the prior written permission of the publisher.The American Society of Mechanical EngineersThree Park Avenue,Ne
9、w York,NY 10016-5990Copyright 2009 byTHE AMERICAN SOCIETY OF MECHANICAL ENGINEERSAll rights reservedPrinted in U.S.A.Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford
10、University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.ASME B5.60b-2009Following approval by the ASME B5 Committee and ASME,and after public review,ASME B5.60b-2009was approved by the Ame
11、rican National Standards Institute on February 2,2009.Addenda to the 2002 edition of ASME B5.60 are issued in the form of replacement pages.Revisions,additions,and deletions are incorporated directly into the affected pages.It is advisable,however,that thispage,the Addenda title and copyright pages,
12、and all replaced pages be retained for reference.SUMMARY OF CHANGESThis is the second Addenda to be published to ASME B5.60-2002.The first Addenda was published in 2005.Replace or insert the pages listed.Changes given below are identified on the pages by a margin note,(b),placed next to the affected
13、 area.Previous Addenda changes are indicated by(a).The pages not listed arethe reverse sides of the listed pages and contain no changes.PageLocationChangeiiiContentsUpdated to reflect AddendaivForewordUpdated to reflect AddendavCommittee RosterUpdated to reflect AddendaviiPrefaceUpdated to reflect A
14、ddenda4.14.33ASME B5.60.3Added(c)Copyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University
15、User.No further reproduction or distribution is permitted.Uncontrolled when printed.INTENTIONALLY LEFT BLANKCopyright 2009 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.cCopyrighted material licensed to Stanford Universit
16、y by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.CONTENTS(a)(b)Foreword.ivStandards Committee Roster.vCorrespondence With the B5 Committee.viPreface.viiASME B5.60.1General Description and Definitions of Terms.1ASME B5.60.2Chuck-to-Spindle Interface(to be added).ASME B5.60.3Jaw Mountings.4.1ASME B5.60.4Performance Testing.5ASME B5.60.5Safety Code of Practice.11ASME B5.60.6Chuck Assembly:S
