1、Designation:D77011(Reapproved 2019)Standard Specification forIsopropyl Alcohol1,2This standard is issued under the fixed designation D770;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenthes
2、es indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers isopropyl alcohol(99%grade).1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are includ
3、ed in thisstandard.1.3 The following applies to all specified limits in thisstandard:for purposes of determining conformance with thisstandard,an observed value or a calculated value shall berounded off“to the nearest unit”in the last right-hand digitused in expressing the specification limit,in acc
4、ordance withthe rounding-off method of Practice E29.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the appli
5、cability of regulatory limitations prior to use.1.5 For hazard information and guidance,see the suppliersMaterial Safety Data Sheet.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles fo
6、r theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D268 Guide for Sampling and Testing Volatile Solvents andChemical Intermediates for Use in Paint and Relat
7、edCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids(Platinum-Cobalt Scale)D1296 Test Method for Odor of Volatile Solvents andDiluentsD1353 Test Method for Nonvolatile Matter in Volatile Sol-vents for Use in Paint,Va
8、rnish,Lacquer,and RelatedProductsD1364 Test Method for Water in Volatile Solvents(KarlFischer Reagent Titration Method)D1476 Test Method for Heptane Miscibility of LacquerSolventsD1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint,Varnish,Lacquer,and Related Pr
9、oductsD1722 Test Method for Water Miscibility of Water-SolubleSolventsD4052 Test Method for Density,Relative Density,and APIGravity of Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine
10、 Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S.Federal Specification:4PPP-C-2020 Chemicals,Liquid,Dry,and Paste:Packagingof3.Properties3.1 Isopropyl alcohol shall conform to the following re-quirements:Apparent specific gravity,20/20 C0.785 to 0.787or25/25 C0.
11、782 to 0.784Color,Pt-Co scale,maxA10Distillation range,760 mmHgBNonvolatile matter,max,mg/100 mL5OdornonresidualCWater,max,weight%0.2DAcidity,acetic acid,max,weight%0.002EWater miscibilitypasses test1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Mate
12、rials,and Applications and is the direct responsibility ofSubcommittee D01.35 on Solvents,Plasticizers,and Chemical Intermediates.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 1944.Last previous edition approved in 2011 as D770 11.DOI:10.1520/D0770-11R19.2This comp
13、ound is also known under the name propanol-2 and isopropanol.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Avai
14、lable from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordanc
15、e with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 AInstrumental Pt-Co color determined b
16、y Test Method D5386 has been shown tohave no statistically significant difference from Pt-Co color determined by TestMethod D1209.However,it is not known whether isopropyl alcohol was part of thesample set included in the interlaboratory study.BDistill entirely within a 1.5 C range which shall include 82.3 C.COptional,when required,as agreed upon between the supplier and theconsumer.DThis quantitative water limit ensures that the material is miscible without turbiditywith 19 volumes of 99%heptan
