1、Designation:D775511(Reapproved 2017)Standard Practice forDetermining the Wear Volume on Standard Test Pieces Usedby High-Frequency,Linear-Oscillation(SRV)Test Machine1This standard is issued under the fixed designation D7755;the number immediately following the designation indicates the year oforigi
2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This practice covers a procedure for determining thewear volume WVof we
3、ar scars and tracks on test piecestribologically stresses under high-frequency,linear-oscillationmotion using a SRV test machine by means of stylus tipprofilometry.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This stan
4、dard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard
5、 was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Reference
6、d Documents2.1 ASTM Standards:2D2714 Test Method for Calibration and Operation of theFalex Block-on-Ring Friction and Wear Testing MachineD2782 Test Method for Measurement of Extreme-PressureProperties of Lubricating Fluids(Timken Method)D3702 Test Method for Wear Rate and Coefficient of Fric-tion o
7、f Materials in Self-Lubricated Rubbing ContactUsing a Thrust Washer Testing MachineD4175 Terminology Relating to Petroleum Products,LiquidFuels,and LubricantsD5620 Test Method for Evaluating Thin Film Fluid Lubri-cants in a Drain and Dry Mode Using a Pin and Vee BlockTest Machine(Withdrawn 2010)3D57
8、06 Test Method for Determining Extreme PressureProperties of Lubricating Greases Using a High-Frequency,Linear-Oscillation(SRV)Test MachineD5707 Test Method for Measuring Friction and Wear Prop-erties of Lubricating Grease Using a High-Frequency,Linear-Oscillation(SRV)Test MachineD6425 Test Method f
9、or Measuring Friction and Wear Prop-erties of Extreme Pressure(EP)Lubricating Oils UsingSRV Test Machine2.2 DIN Standards:4DIN 51631:1999-04 Special-boiling-point spirit Require-ments and testingDIN 51834-3:2008-12 Testing of lubricants Tribologicaltest in translatory oscillation apparatus Part 3:De
10、termi-nation of tribological behaviour of materials in co-operation with lubricantsDIN EN ISO 13565-2:1998 Geometrical Product Specifica-tions(GPS)Surface texture:Profile method;Surfaceshaving stratified functional properties Part 2:Heightcharacterization using linear material ratio curve(replacesof
11、 DIN 4776:1990:Measurement of surface roughness;parameters RK,RPK,RVK,Mr1,Mr2for the description ofthe material portion)3.Terminology3.1 Definitions:3.1.1 Hertzian contact area,nthe apparent area of contactbetween two non-conforming solid bodies pressed against eachother.3.1.2 Hertzian contact press
12、ure,nmagnitude of the pres-sure at any specified location in a Hertzian contact area,ascalculated from Hertzs equations of elastic deformation.TheHertzian contact pressure can also be calculated and reported1This practice is under the jurisdiction of ASTM Committee D02 on PetroleumProducts,Liquid Fu
13、els,and Lubricants and is the direct responsibility of Subcom-mittee D02.L0 on Industrial Lubricants and Engineering Sciences of High Perfor-mance Fluids and Solids.Current edition approved June 1,2017.Published July 2017.Originally approvedin 2011.Last previous edition approved in 2011 as D7755 11.
14、DOI:10.1520/D7755-11R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this histori
15、cal standard is referenced onwww.astm.org.4Available from Deutsches Institut fur Normung e.V.(DIN),Beuth VerlagGmbH,Burggrafenstrae 6,D-10787 Berlin 30,Germany,http:/www.din.de.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis internatio
16、nal standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 as maximum value Pmaxin the centre of the contact or asPaverageas average over the total contact area.D41753.1.3 seizure,nlocalized fusion of metal between therubbing surfaces of the test pieces.D570
