收藏 分享(赏)

ASTM_D_7946_-_19.pdf

上传人:益****师 文档编号:173819 上传时间:2023-03-04 格式:PDF 页数:5 大小:97.37KB
下载 相关 举报
ASTM_D_7946_-_19.pdf_第1页
第1页 / 共5页
ASTM_D_7946_-_19.pdf_第2页
第2页 / 共5页
ASTM_D_7946_-_19.pdf_第3页
第3页 / 共5页
ASTM_D_7946_-_19.pdf_第4页
第4页 / 共5页
ASTM_D_7946_-_19.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D794619Standard Test Method forInitial pH(i-pH)-Value of Petroleum Products1This standard is issued under the fixed designation D7946;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in p

2、arentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers procedures for the determina-tion of initial pH(i-pH)in new and in-service lubricants.NOTE1In new and used oils,the constitue

3、nts that may be consideredto have characteristics influencing the i-pH value include organic andinorganic acids,esters,phenolic compounds,lactones,resins,salts ofheavy metals,salts of ammonia and other weak bases,acid salts ofpolybasic acids,and addition agents such as inhibitors and detergents.“Ini

4、tial”is used to differentiate from aqueous systems.The analysis isterminated after a defined time interval whenever equilibrium conditions,as known for pH measurements in aqueous systems,are not reached(see3.1.1.2)1.2 This test method is used to indicate relative changes thatoccur in oil during use

5、under oxidizing conditions or due tocontamination by blow-by gases of combustion processes ofbiogases regardless of the color or other properties of thein-service lubricants.Although the initial pH is made underdefinite equilibrium conditions,the test method is not intendedto measure an absolute aci

6、dic property that can be used topredict performance of oil under service conditions.No generalcorrelation between corrosion of non-ferrous bearing metalsand initial pH value is known.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thissta

7、ndard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to us

8、e.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers t

9、o Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD4057 Practice for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum Products3.Terminology3.1 Definitions:3.1.1 initial pH(i-pH),nthe m

10、easure of the hydrogen ion(H+)concentration when a fixed sample amount of lubricationoil is dissolved into a fixed volume of solvent and using aspecified detection system.3.1.1.1 DiscussionThis test method expresses the amountof dissociated acidic components as i-pH of a sample in amixture of toluen

11、e and propan-2-ol to which a small amount ofwater has been added.3.1.1.2 DiscussionThe measured i-pH is called initialsince the original definition of the pH-scale depends onaqueous solutions.Its application to organic solutions will notgive stable electrode potential for all types of samples.Apoten

12、tial reading after a defined time is used in those casesinstead.4.Summary of Test Method4.1 The oil sample is dissolved in solvent mixture and thei-pH value is measured using a glass indicating electrode anda reference electrode or a combination electrode.The meterreadings are measured manually or a

13、utomatically.5.Significance and Use5.1 New and used petroleum products may contain acidicconstituents that are present as additives,degradation productsformed during service,such as oxidation products or compo-nents formed from combustion gases.The i-pH-value is ameasure of the amount of acidic subs

14、tances and their aciditydefined under the conditions of test.The i-pH-value is used asa measure of lubricant degradation in service.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.0

15、6 on Analysis of Liquid Fuels and Lubricants.Current edition approved Dec.1,2019.Published January 2020.Originallyapproved in 2014.Last previous edition approved in 2014 as D7946 14.DOI:10.1520/D7946-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Servic

16、e at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of Internat

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2