收藏 分享(赏)

ASTM_D_5293_-_20.pdf

上传人:益****师 文档编号:177383 上传时间:2023-03-04 格式:PDF 页数:12 大小:476.81KB
下载 相关 举报
ASTM_D_5293_-_20.pdf_第1页
第1页 / 共12页
ASTM_D_5293_-_20.pdf_第2页
第2页 / 共12页
ASTM_D_5293_-_20.pdf_第3页
第3页 / 共12页
ASTM_D_5293_-_20.pdf_第4页
第4页 / 共12页
ASTM_D_5293_-_20.pdf_第5页
第5页 / 共12页
ASTM_D_5293_-_20.pdf_第6页
第6页 / 共12页
亲,该文档总共12页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation:D529320Standard Test Method forApparent Viscosity of Engine Oils and Base StocksBetween 10 C and 35 C Using Cold-Cranking Simulator1This standard is issued under the fixed designation D5293;the number immediately following the designation indicates the year oforiginal adoption or,in the

2、case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This test method covers the laboratory determination ofapparent viscosity of engine oils and

3、base stocks by coldcranking simulator(CCS)at temperatures between 10 C and35 C at shear stresses of approximately 50 000 Pa to100 000 Pa and shear rates of approximately 105to 104s1forviscosities of approximately 900 mPas to 25 000 mPas.Therange of an instrument is dependent on the instrument modela

4、nd software version installed.Apparent Cranking Viscosityresults by this method are related to engine-cranking charac-teristics of engine oils.1.2 A special procedure is provided for measurement ofhighly viscoelastic oils in manual instruments.See AppendixX2.1.3 Procedures are provided for both manu

5、al and automateddetermination of the apparent viscosity of engine oils using thecold-cranking simulator.1.4 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns,i

6、f any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.Specific warning statements are given in Section 8.1.6 This international sta

7、ndard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Refe

8、renced Documents2.1 ASTM Standards:2D2162 Practice for Basic Calibration of Master Viscometersand Viscosity Oil StandardsD2602 Test Method for Apparent Viscosity of Engine OilsAt Low Temperature Using the Cold-Cranking Simulator(Withdrawn 1993)3D4057 Practice for Manual Sampling of Petroleum andPetr

9、oleum Products2.2 ISO Standard:ISO 17025 General Requirements for the Competence ofTesting and Calibration Laboratories43.Terminology3.1 Definitions:3.1.1 Newtonian oil,nan oil or fluid that at a giventemperature exhibits a constant viscosity at all shear rates orshear stresses.3.1.2 non-Newtonian o

10、il,nan oil or fluid that at a giventemperature exhibits a viscosity that varies with changing shearstress or shear rate.3.1.3 viscosity,nthe ratio between the applied shear stressand rate of shear which is sometimes called the coefficient ofdynamic viscosity and is a measure of the resistance to flo

11、w ofthe liquid.3.1.3.1 DiscussionIt is sometimes called the coefficient ofdynamic viscosity.This coefficient is thus a measure of theresistance to flow of the liquid.In the SI,the unit of viscosityis the pascal-second;for practical use,a submultiple(millipascal-second)is more convenient and is custo

12、marilyused.The millipascal second is 1 cP(centipoise).3.2 Definitions of Terms Specific to This Standard:3.2.1 apparent viscosity,nthe viscosity obtained by use ofthis test method.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and i

13、s the direct responsibility ofSubcommittee D02.07 on Flow Properties.Current edition approved June 1,2020.Published June 2020.Originallyapproved in 1991.Last previous edition approved in 2017 as D5293 17a.DOI:10.1520/D5293-20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orconta

14、ct ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute(AN

15、SI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with i

16、nternationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.3.2.1.1 DiscussionSince many engine oils are non-Newtonian at low temperature,apparent viscosity can varywith shear rate.3.2.2 calibration oils,noils with known viscosity andviscosity/temperature functionality that are used to define thecalibration

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2