1、Designation:D463416(Reapproved 2022)Standard Classification System and Basis for Specification forStyrene-Maleic Anhydride Molding and Extrusion Materials(S/MA)1This standard is issued under the fixed designation D4634;the number immediately following the designation indicates the year oforiginal ad
2、option or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.S
3、cope1.1 This classification system covers styrene-maleic anhy-dride materials suitable for molding or extrusion.This classi-fication system does not apply to alloys or blends of styrene-maleicanhydridematerialswithnon-elastomericthermoplastics.Styrene-maleic anhydride materials,beingthermoplastic,ar
4、e reprocessable and recyclable.This classifi-cation system allows for the use of those materials providedthat all the specific requirements of this classification systemare met.1.2 The properties included in this standard are thoserequired to identify the compositions covered.Other require-ments nec
5、essary to identify particular characteristics importantto specialized applications are to be specified by using thesuffixes as given in Section 5.1.3 This classification system and subsequent line call out(specification)are intended to provide means of calling outproperties of plastic materials used
6、 in the fabrication of enditems or parts.It is not intended for the selection of materials.Materials should be selected by those having expertise in theplastics field after careful consideration of the design and theperformance required of the part,the environment to which itwill be exposed,the fabr
7、ication process to be employed,costsinvolved,and the inherent properties of the material other thanthose covered by this classification system.1.4 The values stated in SI units are to be regarded as thestandard.1.5 The following precautionary caveat pertains only to thetest methods portion,Section 1
8、1,of this classification system.This standard does not purport to address all of the safetyconcerns,if any,associated with its use.It is the responsibilityof the user of this standard to establish appropriate safety,health,and environmental practices and determine the appli-cability of regulatory li
9、mitations prior to use.NOTE1There is no known ISO equivalent to this standard.1.6 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and
10、 Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D256 Test Methods for Determining the Izod PendulumImpact Resistance of PlasticsD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensile
11、Properties of PlasticsD648 Test Method for Deflection Temperature of PlasticsUnder Flexural Load in the Edgewise PositionD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD883 Terminology Relating to PlasticsD1525 Test Method for Vic
12、at Softening Temperature ofPlasticsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD3641 Practice for Injection Molding Test Specimens ofThermoplastic Molding and Extrusion MaterialsD3892 Practice for Packaging/Packing of PlasticsD4000 Classification System for Specifying Plastic Materi-
13、alsD7209 Guide for Waste Reduction,Resource Recovery,andUse of Recycled Polymeric Materials and Products(With-drawn 2015)3E29 Practice for Using Significant Digits in Test Data toDetermine Conformance with Specifications1This classification system is under the jurisdiction ofASTM Committee D20 onPla
14、stics and is the direct responsibility of Subcommittee D20.15 on ThermoplasticMaterials.Current edition approved Sept.1,2022.Published September 2022.Originallyapproved in 1986.Last previous edition approved in 2016 as D4634-16.DOI:10.1520/D4634-16R22.2For referenced ASTM standards,visit the ASTM we
15、bsite,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section
16、appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.12.2 Military Standard:4MIL-STD-1916 DOD Pr
