收藏 分享(赏)

ASTM_D_5325_-_03_2014.pdf

上传人:益****师 文档编号:177864 上传时间:2023-03-04 格式:PDF 页数:2 大小:81.85KB
下载 相关 举报
ASTM_D_5325_-_03_2014.pdf_第1页
第1页 / 共2页
ASTM_D_5325_-_03_2014.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D532503(Reapproved 2014)Standard Test Method forDetermination of Weight Percent Volatile Content of Water-Borne Aerosol Paints1This standard is issued under the fixed designation D5325;the number immediately following the designation indicates the year oforiginal adoption or,in the case

2、of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is for the determination of the weightpercent volatile content of water-borne pain

3、ts in aerosols.1.2 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to est

4、ablish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D2369 Test Method for Volatile Content of CoatingsD3792 Test Method for Water Content of Coatings by DirectInjection Into a Gas Chromatogr

5、aphD4017 Test Method for Water in Paints and Paint Materialsby Karl Fischer MethodE180 Practice for Determining the Precision of ASTMMethods for Analysis and Testing of Industrial and Spe-cialty Chemicals(Withdrawn 2009)32.2 Other Standard:Method 36 Determination of Percent Volatile Organic Com-poun

6、ds(VOC)in Water Based Aerosol Paints43.Summary of Test Method3.1 The propellant is released from the can and the contentremaining is tested for percent water and nonvolatiles.4.Significance and Use4.1 Calculation of the weight percent volatile organic con-tent of water-borne paints,requires that the

7、 water content beknown.This test method provides a direct way to determine theweight percent volatile organic matter of water-borne aerosolpaints minus the matter content.This test method is modeledafter Method 36.45.Apparatus5.1 Freezer.5.2 Ice Pick.5.3 Hammer.5.4 Applicator Sticks.5.5 Masking Tape

8、.5.6 Tin Snips or Metal Cutter.5.7 Shaker,similar to Eberbach shaker in Fig.1.6.Procedure6.1 Preparation of Aerosol Contents for Analysis:6.1.1 Mix the aerosol paint container thoroughly for about15 min,using a shaker similar to the Eberbach shaker shown inFig.1,at the low speed setting.It is essent

9、ial that the samplesbe well mixed to obtain valid results.6.1.2 Remove the cap and actuator from the can.Put the capon the can and weigh the can to 0.01 g.6.1.3 Place the can in an upside down position in a freezerfor 2 h at a temperature that is 0C.6.1.4 Put the can upside down in a fume hood.Punct

10、ure thebottom of the can near the edge with a very sharp ice pick.Slowly remove the ice pick from the hole.Leave the holeuncovered for about 12 to 16 h to allow most of the propellantto escape.6.1.5 Enlarge the hole slightly by tapping the ice pickfurther into the can.Swirl the can gently for 1 to 2

11、 min toremove any remaining propellant.6.1.6 Wipe off any condensate that may have accumulatedon the can.Weigh the can to 60.01 g.6.1.7 Plug the hole with a small applicator stick(about12cm long)and then place masking tape over the plugged hole.1This test method is under the jurisdiction of ASTM Com

12、mittee D01 on Paintand Related Coatings,Materials,and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved July 1,2014.Published July 2014.Originally approvedin 1992.Last previous edition approved in 2008 as D

13、5325 03(2008)1.DOI:10.1520/D5325-03R14.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version

14、of this historical standard is referenced onwww.astm.org.4Bay Area Air Quality Management District,(BAAQMD)Manual ofProcedures,Vol III,939 Ellis St.,San Francisco,CA 94109.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.1.8 Place the ca

15、n on the shaker in a position so that thehole is at the highest possible position to prevent leakage ofcontents.Shake the can for about 15 min at the low speedsetting.6.1.9 Cut the bottom of the can using a metal cutter.Stir thecontents with a spatula,then transfer the contents to a pint canwith lid

16、.6.1.10 Rinse the aerosol can,agitators,and bottom severaltimes using solvent.Allow the can,agitators,and the bottom todry.Weigh to 60.01 g.7.Calculations7.1 Calculate the weight percent nonvolatile content(NV),of the paint in accordance with Test Method D2369.7.2 Calculate the total weight percent nonvolatile content(TNV),in the aerosol can as follows:TNV,%5NV!W5!W43100(1)where:W4=W1 W3,W5=W2 W3,W1=total weight of aerosol container plus contents,g,W2=total weight of aerosol container minus prop

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2