1、Designation:D3715/D3715M98(Reapproved 2019)Standard Practice forQuality Assurance of Pressure-Sensitive Tapes1This standard is issued under the fixed designation D3715/D3715M;the number immediately following the designation indicates theyear of original adoption or,in the case of revision,the year o
2、f last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This practice contains uniform quali
3、ty assurance provi-sions for pressure-sensitive tapes and establishes samplingplans and procedures for acceptance inspection.1.2 Limitations:1.2.1 This practice only includes procedures for when anupper or a lower specification limit is given.It does not providefor double,both minimum and maximum,sp
4、ecification limits.NOTE1When double specification limits are given(applies tovariables testing only),use may be made of Table C-3 and Example C-3of ANSI/ASQC Z1.9.1.2.2 The variables sampling plans apply to a single qualitycharacteristic.Having obtained the sample and the responses tothe physical pr
5、operty tests,acceptance is determined on onequality characteristic at a time.The process is repeated for eachadditional characteristic.1.2.3 The variables sampling plans require that the responseto each quality characteristic is normally distributed eitherdirectly or by transformation.If this is not
6、 known,the potentialuser of this practice should seek the counsel of someone withsufficient understanding of statistical techniques to provide thatinformation.1.3 The values stated in either SI or inch-pound units are tobe regarded separately as standard.The values stated in eachsystem may not be ex
7、act equivalents;therefore,each systemmust be used independently,without combining values in anyway.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and e
8、nvironmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Sta
9、ndards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D996 Terminology of Packaging and Distribution Environ-ments2.2 ANSI/ASQC Standards:ANSI/ASQC A2 Terms,Symbols,and Definitions for Ac-ceptance
10、Sampling3ANSI/ASQC A3 Quality Systems Terminology4ANSI/ASQC Q94 Quality Management and Quality SystemElementsGuidelines4ANSI/ASQC Z1.4 Sampling Procedures and Tables for In-spection by Attributes4ANSI/ASQC Z1.9 Sampling and Tables for Inspection byVariables for Percent Defective3.Terminology3.1 Defi
11、nitionsGeneral terms in this practice are definedin Terminology D996,ANSI/ASQC A2,and ANSI/ASQC A3.3.2 Definitions of Terms Specific to This Standard:3.2.1 acceptability criterionthe comparison made be-tween a factor,number,or constant found in the sampling planand the examination or test result inf
12、ormation from a singlequality characteristic to determine if the lot should be acceptedor rejected.For inspection by attributes the acceptabilitycriterion is a comparison with the acceptability constant foundin Table 1.3.2.2 acceptable quality level(AQL)a nominal value ex-pressed in terms of percent
13、 defective or defects per hundredunits,whichever is applicable,specified for a given group ofdefects of a product(see ANSI/ASQC A2).1This practice is under the jurisdiction of ASTM Committee D10 on Packagingand is the direct responsibility of Subcommittee D10.14 on Tape and Labels.Current edition ap
14、proved Aug.1,2019.Published August 2019.Originallypublished in 1978.Last previous edition approved as D3715 98(2011).DOI:10.1520/D3715_D3715M-98R19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards v
15、olume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5094,Attn:NPODS.4Available fromAmerican Society for Quality(ASQ),310 West WisconsinAve.,Milwaukee,WI 53203.Cop
16、yright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 3.2.3 defectany nonconformance of the unit of product tospecified requirements;