1、Designation:D289092(Reapproved 2013)Standard Test Method forCalculation of Liquid Heat Capacity of Petroleum DistillateFuels1This standard is issued under the fixed designation D2890;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,th
2、e year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers the calculation of liquid heatcapacity,Btu/lb F(kJ/kg K),at atmospheric pressure,ofpetrol
3、eum fuels for which distillation data may be obtained inaccordance with Test Method D86 without reaching a decom-position point prior to obtaining 90 volume%distilled.1.2 This test method is not applicable at temperatures lessthan 0F(18C)and greater than 60F(16C)above thevolumetric average boiling p
4、oint of the fuel.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.4 This standard does not purport to address all of thesafety concer
5、ns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D86 Test Method for Distillation of Petroleum
6、 Products atAtmospheric PressureD287 Test Method for API Gravity of Crude Petroleum andPetroleum Products(Hydrometer Method)3.Summary of Test Method3.1 The Watson characterization factor,K,is obtained froma graphical correlation relating determined Test Method D86distillation data and K.The liquid h
7、eat capacity is obtained,either graphically or mathematically,from correlations relatingcalculated heat capacity,temperature at which heat capacity isbeing calculated,determined API gravity,and K.NOTE1Details of the method have been published.34.Significance and Use4.1 Heat capacities obtained by th
8、is method are those atatmospheric pressure.However,because the temperature rangeis low,the calculated values are similar to saturated liquid heatcapacities in the temperature-pressure range required for mostengineering design.5.Data Requirements5.1 Distillation temperatures at(in F)10,30,50,70,and 9
9、0volume%distilled obtained in accordance with Test MethodD86.5.2 API gravity determined in accordance with Test MethodD287 or a method of equivalent accuracy.6.Procedure6.1 Calculate to the nearest 0.1 unit the slope of the TestMethod D86 distillation curve,F/volume%,as the differencebetween the 10
10、and 90 volume%distilled temperatures di-vided by 80.6.2 Calculate to the nearest 1F the volumetric averageboiling point(VABP)as the sum of Test Method D86 10,30,50,70,and 90 volume%distilled temperatures divided by 5.6.3 Obtain a temperature correction to the nearest 1F fromFig.1,using the slope and
11、 VABPcalculated in accordance with6.1 and 6.2.Calculate the mean average boiling point(Me-ABP)as the VABP plus the correction.6.4 Obtain to the nearest 0.1 unit the Watson characteriza-tion factor,K,from Fig.2 using the determined API gravityand calculated MeABP.6.5 Obtain the calculated heat capaci
12、ty at each specifiedtemperature,either graphically from Fig.3 or by solving thefollowing equation:1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.04.0K on Correlative Methods.Current edition app
13、roved May 1,2013.Published August 2013.Originallyapproved in 1970.Last previous edition approved in 2008 as D2890 92(2008).DOI:10.1520/D2890-92R13.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards vo
14、lume information,refer to the standards Document Summary page onthe ASTM website.3Technical Data Book-Petroleum Refining,Chapter 7,American PetroleumInstitute,Division of Refining,1220 L St.NW,Washington,DC 20005.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 194
15、28-2959.United States1 Cp50.68112 0.308 G10.0008152 0.000306 G!T#(1)0.055 K10.35!where:Cp=heat capacity,Btu/lb F,G=specific gravity,T=temperature,F,andK=Watson characterization factor.NOTE2The broken lines in Fig.3 illustrate the graphical procedurefor the following example:Calculate the heat capaci
16、ty at atmospheric pressure and 190F of apetroleum distillate fuel having anAPI gravity of 40 and Test Method D86distillation temperatures of 239,261,288,321,and 367 F at 10,30,50,70,and 90 volume%distilled,respectively.The volumetric average boilingpoint(VABP)is 295F,and the slope is 1.60.The temperature correctionobtained from Fig.1 is 9F,and the mean average boiling point is 286F.The value of K obtained from Fig.2 is 11.0.The heat capacity obtained asshown in Fig.3 is 0.51 Btu/lb F.7.Report7.1
