1、Designation:D2513141Standard Specification forPolyethylene(PE)Gas Pressure Pipe,Tubing,and Fittings1This standard is issued under the fixed designation D2513;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A
2、 number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTEFootnote A in Table 4 was editorially corrected in July 2014.1.Scope*1.1 This specification covers requirements and test methodsfor material dim
3、ensions and tolerances,hydrostatic burststrength,chemical resistance,and rapid crack resistance ofpolyethylene pipe,tubing,and fittings for use in fuel gas mainsand services for direct burial and reliner applications.The pipeand fittings covered by this specification are intended for use inthe distr
4、ibution of natural gas.Requirements for the qualifyingof polyethylene systems for use with liquefied petroleum gasare also covered.1.1.1 This specification does not cover threaded pipe.De-sign considerations are discussed in Appendix X1.In-plantquality control programs are specified in Annex A1 and
5、AnnexA2.1.1.2 See Specification F2619/F2619M for polyethylenepiping for pressure or non-pressure oil and gas producingapplications to convey fluids such as oil,dry or wet gas,multiphase fluids,and non-potable oilfield water.1.2 The text of this specification references notes,footnotes,and appendixes
6、 which provide explanatory material.Thesenotes and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.3 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI uni
7、ts that are provided for information onlyand are not considered standard.1.4 The following is an index of the annexes and appendixin this specification:AnnexSubjectAnnex A1In-Plant Quality Control for all materials up to 12 in.Annex A2In-Plant Quality Control for PE materials 14 in.and larger.Append
8、ixesSubjectAppendixX1Design Consideration1.5 The following precautionary caveat pertains only to thetest method portion,Section 6,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this stand
9、ard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 ASTM Standards:22.1.1Terminology:D1600 Terminology forAbbreviated Terms Relating to Plas-ticsF412 Terminology Relating to Plastic Piping Systems2.
10、1.2Test Methods for:D638 Test Method for Tensile Properties of PlasticsD1238 Test Method for Melt Flow Rates of Thermoplasticsby Extrusion PlastometerD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure
11、of Plastic Pipe,Tubing,and FittingsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2290 Test Method for Apparent Hoop Tensile Strength ofPlastic or Reinforced Plastic PipeD2837 Test Method for Obtaining Hydrostatic Design Basisfor Thermoplastic Pipe Materials or Pres
12、sure Design Basisfor Thermoplastic Pipe ProductsF1473 Test Method for Notch Tensile Test to Measure theResistance to Slow Crack Growth of Polyethylene Pipesand Resins2.1.3Practices for:D543 Practices for Evaluating the Resistance of Plastics toChemical ReagentsD618 Practice for Conditioning Plastics
13、 for TestingD1435 Practice for Outdoor Weathering of PlasticsD1898 Practice for Sampling of Plastics(Withdrawn 1998)31This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.60 on Gas.Current edition approved Ap
14、ril 25,2014.Published May 2014.Originallyapproved in 1966.Last previous edition approved in 2013 as D2513 13.DOI:10.1520/D2513-14E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume informati
15、on,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA
16、19428-2959.United States1 D2774 Practice for Underground Installation of Thermoplas-tic Pressure PipingD2565 Practice for Xenon-Arc Exposure of Plastics In-tended for Outdoor ApplicationsF2620 Practice for Heat Fusion Joining of Polyethylene Pipeand FittingsG155 Practice for Operating Xenon Arc Light Apparatus forExposure of Non-Metallic Materials2.1.4Specification for:D2683 Specification for Socket-Type Polyethylene Fittingsfor Outside Diameter-Controlled Polyethylene Pipe andTubingD3261 Specif
