收藏 分享(赏)

ASTM_D_2466_-_17.pdf

上传人:益****师 文档编号:180885 上传时间:2023-03-04 格式:PDF 页数:6 大小:142.63KB
下载 相关 举报
ASTM_D_2466_-_17.pdf_第1页
第1页 / 共6页
ASTM_D_2466_-_17.pdf_第2页
第2页 / 共6页
ASTM_D_2466_-_17.pdf_第3页
第3页 / 共6页
ASTM_D_2466_-_17.pdf_第4页
第4页 / 共6页
ASTM_D_2466_-_17.pdf_第5页
第5页 / 共6页
ASTM_D_2466_-_17.pdf_第6页
第6页 / 共6页
亲,该文档总共6页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D246617An American National StandardStandard Specification forPoly(Vinyl Chloride)(PVC)Plastic Pipe Fittings,Schedule401This standard is issued under the fixed designation D2466;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revi

2、sion,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This specification c

3、overs poly(vinyl chloride)(PVC)Schedule 40 pipe fittings.Included are requirements formaterials,workmanship,dimensions,and burst pressure.NOTE1Socket-type CPVC plastic pipe fittings,Schedule 40,whichwere formerly included in this standard,are now covered by SpecificationF438.1.2 The products covered

4、 by this specification are intendedfor use with the distribution of pressurized liquids only,whichare chemically compatible with the piping materials.Due toinherent hazards associated with testing components and sys-tems with compressed air or other compressed gases,somemanufacturers do not allow pn

5、eumatic testing of their products.Consult with specific product/component manufacturers fortheir specific testing procedures prior to pneumatic testing.NOTE2Pressurized(compressed)air or other compressed gasescontain large amounts of stored energy which present serious safteyhazards should a system

6、fail for any reason.1.3 Fitting such as unions,flanges,special plastic-to-metaltransitions and appurtenances intended for use with PVCpiping are covered under specification F1970.1.4 The text of this specification references notes,footnotes,and appendixes which provide explanatory material.Thesenote

7、s and footnotes(excluding those in tables and figures)shallnot be considered as requirements of the specification.1.5 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand

8、are not considered standard.1.6The following safety hazards caveat pertains only tothe test method portion,Section 7,of this specification.Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this standard to establ

9、ish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.1.7 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment

10、of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plas

11、tic Pipe,Tubing,and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride)(PVC)Compounds and Chlorinated Poly(Vinyl Chloride)(CPVC)CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2749 Symbols fo

12、r Dimensions of Plastic Pipe FittingsF412 Terminology Relating to Plastic Piping SystemsF438 Specification for Socket-Type Chlorinated Poly(VinylChloride)(CPVC)Plastic Pipe Fittings,Schedule 40F1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and FittingsF1970 Specification for S

13、pecial Engineered Fittings,Appur-tenances or Valves for use in Poly(Vinyl Chloride)(PVC)or Chlorinated Poly(Vinyl Chloride)(CPVC)Systems2.2NSF Standards:Standard No.14 for Plastic Piping Components and RelatedMaterials31This specification is under the jurisdiction of ASTM Committee F17 on PlasticPip

14、ing Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approved Aug.1,2017.Published August 2017.Originallyapproved in 1965.Last previous edition approved in 2015 as D2466 15.DOI:10.1520/D2466-17.2For referenced ASTM standards,visit the ASTM website,www.astm.

15、org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from NSF International,P.O.Box 130140,789 N.Dixboro Rd.,AnnArbor,MI 48113-0140,http:/www.nsf.org.*A Summary of Changes

16、 section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 Standard No.61 for Drinking Wate

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2