1、Designation:D 3601 88(Reapproved 2002)e1An American National StandardStandard Test Method forFoam In Aqueous Media(Bottle Test)1This standard is issued under the fixed designation D 3601;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revisio
2、n,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon(e)indicates an editorial change since the last revision or reapproval.e1NOTEWarning notes were placed in the text editorially in May 2002.1.Scope1.1 This test method covers the measurement
3、of the increasein volume of a low-viscosity aqueous liquid(less than 3 cSt at40C)due to its tendency to foam under low shear conditions.NOTE1Foam under high shear is covered by Test Method D 3519which uses a commercial blender.1.2 The values stated in SI units are to be regarded as thestandard.The v
4、alues given in parentheses are provided forinformation only.1.3This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bilit
5、y of regulatory limitations prior to use.For specific safetyinformation,see 7.13.2.Referenced Documents2.1 ASTM Standards:D 1126 Test Method for Hardness in Water2D 3519 Test Method for Foam In Aqueous Media(BlenderTest)33.Summary of Test Method3.1 The increase in volume is determined by the increas
6、e intotal height of the test fluid,including foam,after vigorousshaking of the emulsion at 25 6 1C(77 6 1.8F).NOTE2Water that is normally used to reduce the concentrate to aworking consistency can be used.However,if this type of water is notdesirable or available,two other types of water may be used
7、 to prepare thetest liquid:(1)distilled water or(2)distilled water with a subsequentseeding of the test liquid with synthetic hard water.4.Significance and Use4.1 The results obtained by this test method are useful asguides in determining the tendency of a water-based metal-working coolant to produc
8、e foam under low shear conditions.No correlation with changes in heat transfer,pumpability,orother factors affected by foam is intended.The foam generatedby any given industrial process depends on the method bywhich the foam is generated and may not be directly propor-tional to that produced by this
9、 controlled laboratory testmethod.Further,the foam generated at the specified testtemperature will not necessarily predict the foaming tendencyof the liquid(that is,metalworking coolant)at some other usetemperature.5.Apparatus5.1 Water Bath,constant-temperature,suitable to hold sev-eral bottled emul
10、sions at 25 6 1C(77 6 1.8F)for 1 to 2 h.NOTE3A common household dishpan is satisfactory when the testtemperature is close to room temperature.5.2 Stop Watch or Timer,capable of measuring 5 min 6 0.2s.5.3 Bottles,clean or new,clear glass,16-oz(narrow mouth),with screw neck.4The 16-oz bottle is 64164i
11、n.(169 mm)talland has a maximum diameter of 23132in.(75 mm).The outsideneck is932in.(7.1 mm)and the shoulder radius is 1 in.(25.4mm).1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products and Lubricants and is the direct responsibility of SubcommitteeD02.LO.01 Metal R
12、emoval Fluids and Lubricants.Current edition approved Oct.31,1988.Published January 1989.2Annual Book of ASTM Standards,Vol 11.01.3Annual Book of ASTM Standards,Vol 05.02.416-oz Round Packer,Brockway Glass Co.,Mold No.1094 or 16-oz BostonRound,as shown in Fig.1 is suitable for this purpose.Bottle ta
13、kes Cap No.28.Standard Glass Container Series No.80 specifies approximate weight of glass,etc.,on drawing No.C-8010 obtainable from Glass Container Manufacturers InstituteInc.,330 Madison Ave.,New York,NY 10017.FIG.1 Boston Round Bottle.1Copyright ASTM International,100 Barr Harbor Drive,PO Box C700
14、,West Conshohocken,PA 19428-2959,United States.5.4 Syringe or Transfer Pipet.55.5 Rule,millimetre,at least 150 mm in length.6.Materials6.1 Distilled Water.6.2 Hard Water,20 000 ppm prepared by dissolving 29.4 gof reagent grade(ACS standard)CaCl2 2H2O in 1 litre offreshly boiled distilled water(used
15、only where distilled wateris used as in Note 5).7.Procedure7.1 Fix a label or other means of marking total heights to theoutside of the bottle.NOTE4Waterproof medical adhesive tape makes satisfactory water-proof labels,which readily take pencil marks.67.2 Using the manufacturers recommended procedur
16、e,pre-pare 200 ml of emulsion at the recommended concentrationand pour the emulsion into the 16-oz round bottle(or equiva-lent 500-cm3bottle).7.3 When natural water is used,record water hardness(using Test Method D 1126),source,and date obtained.5Disposable pipets,Thomas Scientific Co.Saedsboro,NJ 08085-0099,No.8937-R62,Corning No.7077 or Fisher No.13-671-108E with attached 25 to 50-cm3(1 to 2-oz)capacity rubber bulb have been found suitable for this purpose as haveBecton-Dickson disposable syri
