1、Designation:D140320bDesignation:310/84(92)Standard Test Methods forCone Penetration of Lubricating Grease Using One-Quarterand One-Half Scale Cone Equipment1This standard is issued under the fixed designation D1403;the number immediately following the designation indicates the year oforiginal adopti
2、on or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope
3、*1.1 These test methods cover two procedures for measuringthe consistency of small samples of lubricating greases bypenetration of a14-scale cone or a12-scale cone.These testmethods include procedures for the measurement of unworkedand worked penetrations.1.2 Unworked penetrations do not generally r
4、epresent theconsistency of greases in use as effectively as do workedpenetrations.The latter are usually preferred for inspectinglubricating greases.1.3 The values in SI units are to be regarded as the standard.The values given in parentheses are for information only.In theUnited States,the equipmen
5、t dimensions stated in inches are tobe regarded as the standard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mi
6、ne the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations
7、issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D217 Test Methods for Cone Penetration of LubricatingGreaseD4175 Terminology Relating to Petroleum Products,LiquidFuels,and Lubricants2.2 Energy Institute Standard:3IP 50 Method
8、of Testing for Cone Penetration of LubricatingGrease3.Terminology3.1 Definitions:3.1.1 consistency,nof lubricating grease,the degree ofresistance to movement under stress.3.1.1.1 DiscussionThe term consistency is used somewhatsynonymously with penetration.Generally,consistency refersto the worked pe
9、netration of a grease.D2173.1.2 lubricant,nany material interposed between twosurfaces that reduces the friction or wear between them.D41753.1.3 lubricating grease,na semi-fluid to solid product ofa dispersion of a thickener in a liquid lubricant.3.1.3.1 DiscussionThe dispersion of the thickener for
10、ms atwo-phase system and immobilizes the liquid lubricant bysurface tension and other physical forces.Other ingredientsimparting special properties are often included.D2173.1.4 penetration,nof lubricating grease,the depth thatthe standard cone,when released to fall under its own weightfor 5 s,enters
11、 the sample.3.1.5 penetrometer,nan instrument that measures theconsistency or hardness of semiliquid to semisolid materials by1These test methods are under the jurisdiction of ASTM Committee D02 onPetroleum Products,Liquid Fuels,and Lubricants and is the direct responsibility ofSubcommittee D02.G0.0
12、2 on Consistency and Related Rheological Tests.In the IP,this test method is under the jurisdiction of the StandardizationCommittee.This test method has been approved by the sponsoring committee andaccepted by the cooperating societies in accordance with established procedures.Current edition approv
13、ed June 1,2020.Published September 2020.Originallyapproved in 1956.Last previous edition approved in 2020 as D1403 20a.DOI:10.1520/D1403-20B.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume i
14、nformation,refer to the standards Document Summary page onthe ASTM website.3Available from Energy Institute,61 New Cavendish St.,London,WIG 7AR,U.K.,http:/www.energyinst.org.uk.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box
15、C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the Wor
16、ld Trade Organization Technical Barriers to Trade(TBT)Committee.measuring the depth to which a specified cone or needle undera given force falls into the material.3.1.5.1 DiscussionEither a14-scale cone(A1.1)or a12-scale cone(A1.3)can be used to determine the consistencyof lubricating greases.The penetration forces are determinedby the respective masses of the cones and shafts.3.1.6 reduced-scale penetration,nof lubricating grease,the depth in units of 0.1 mm that a14-scale cone or12-scalecone p
