收藏 分享(赏)

ASTM_C_315_-_07_2016.pdf

上传人:益****师 文档编号:183881 上传时间:2023-03-04 格式:PDF 页数:3 大小:81.69KB
下载 相关 举报
ASTM_C_315_-_07_2016.pdf_第1页
第1页 / 共3页
ASTM_C_315_-_07_2016.pdf_第2页
第2页 / 共3页
ASTM_C_315_-_07_2016.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:C31507(Reapproved 2016)Standard Specification forClay Flue Liners and Chimney Pots1This standard is issued under the fixed designation C315;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numbe

2、r in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification establishes the criteria for acceptance,

3、prior to installation,of clay flue liners and chimney pots usedfor conveying hot gases in masonry chimneys.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not

4、 considered standard.1.3 For installation of clay flue liners,see Practice C1283.2.Referenced Documents2.1 ASTM Standards:2C67 Test Methods for Sampling and Testing Brick andStructural Clay TileC301 Test Methods for Vitrified Clay PipeC896 Terminology Relating to Clay ProductsC1283 Practice for Inst

5、alling Clay Flue Lining3.Terminology3.1 Definitions:3.1.1 Clay,fire clay,shale,and surface clay are as defined inTerminology C896.3.1.2 chimney pota pipe used at the top of the chimney toincrease draft and carry off smoke.4.Classification4.1 TypesFlue liners acceptable under this specificationshall

6、be designated as rectangular nonmodular,rectangularmodular,round or oval.5.Materials and Manufacture5.1 Flue liners and chimney pots shall be manufacturedfrom fire clay,shale,surface clay,or a combination of thesematerials that when formed and fired to suitable temperatures,shall yield a product tha

7、t is strong,durable,serviceable,andconforms to this specification.6.Physical and Chemical Requirements6.1 Absorption:6.1.1 The absorption of clay flue liners and chimney potsshall not exceed 8.0%when tested in accordance with TestMethods C301.6.1.2 Test SpecimensFive dry test specimens shall beobtai

8、ned from the five flue liners or chimney pots to be testedand shall measure as closely as possible to 4 by 4 in.(100 by100 mm)per side.All rough edges shall be ground off andloose particles removed.6.1.3 If any of the test specimens fail to meet therequirements,the manufacturer shall be allowed to r

9、etest ontwo additional specimens for each one that failed.The flues andpots will be acceptable if all the subsequent specimens forretest meet the requirements.6.2 Acid Resistance:6.2.1 This is a test used to determine the resistance of clayflue liners and chimney pots to the action of acids encounte

10、redin chimneys.This test shall be performed only when specified.6.2.2 The flue liner and chimney pots shall be acceptable ifthe acid soluble material does not exceed 0.25%when testedin accordance with Test Methods C301.6.2.3 Test SpecimensSelect one test specimen from eachsize of flue liner or chimn

11、ey pot.The specimens shall measureabout 2 by 2 in.(51 by 51 mm)per side and weigh not morethan 200 g.They shall be sound pieces with all edges freshlybroken,free of cracks or shattered edges,and shall bethoroughly cleaned.6.3 Freeze-Thaw Cycle Test:6.3.1 When flue liners or chimney pots are tested i

12、n accor-dance with Test Methods C67,Section 9 on structural clay tile,there shall be no breakage and the percentage of weight lossshall not exceed 0.5%.6.3.2 Test SpecimensFive dry test specimens shall beobtained from the five flue liners or chimney pots to be testedand shall measure as closely as p

13、ossible to 4 by 4 in.(100 by100 mm)per side.All rough edges shall be ground off andloose particles removed.1This specification is under the jurisdiction of ASTM Committee C04 onVitrified Clay Pipe and is the direct responsibility of Subcommittee C04.20 onMethods of Test and Specifications.Current ed

14、ition approved Nov.1,2016.Published November 2016.Originallyapproved in 1953.Last previous edition approved in 2011 as C315 07(2011).DOI:10.1520/C0315-07R16.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMSt

15、andards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.Sizes and Dimensions7.1 Flue liners shall be specified and furnished in thedimensions prescribed

16、in Tables 1-4.When other sizes arerequired,flue liners that meet the requirements of Sections 5and 6 shall be cut and installed in the chimney.7.2 Variations in dimensions in Tables 1-4 shall not exceed612in.(613 mm)for outside dimensions.Permissible wallthickness variation is 618in.(63 mm)for all flue liners,except that there shall be no limit for plus variation in roundflue liners.Variations in dimensions of round flue lining shallnot exceed those shown in Table 3.The maximum difference inthe

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2