1、Designation:A971/A971M17Standard Test Method forMeasuring Edge Taper and Crown of Flat-Rolled ElectricalSteel Coils1This standard is issued under the fixed designation A971/A971M;the number immediately following the designation indicates the yearof original adoption or,in the case of revision,the ye
2、ar of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method provides a procedure for measuringedge taper and crown of flat-rolled electrical steel coils asprod
3、uced at the steel mill.1.2 The values and equations stated in customary(cgs-emuand inch-pound)units or SI units are to be regarded separatelyas standard.Within this standard,the SI units are shown inbrackets.The values stated in each system may not be exactequivalents;therefore,each system shall be
4、used independentlyof the other.Combining values from the two systems mayresult in nonconformance with this standard.1.3 The following material specifications include require-ments for edge taper or crown:A677,A683,A726,A876,andA1086.Specification A840 also includes requirements for edgetaper or crow
5、n,but it has been withdrawn and reference to it isincluded for historical purposes.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental pra
6、ctices and deter-mine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides an
7、d Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2A340 Terminology of Symbols and Definitions Relating toMagnetic TestingA677 Specification for Nonoriented Electrical Steel FullyProcessed TypesA683 Specificati
8、on for Nonoriented Electrical Steel,Semi-processed TypesA726 Specification for Cold-Rolled Magnetic LaminationQuality Steel,Semiprocessed TypesA840 Specification for Fully Processed Magnetic Lamina-tion Steel(Withdrawn 2011)3A876 Specification for Flat-Rolled,Grain-Oriented,Silicon-Iron,Electrical S
9、teel,Fully Processed TypesA1086 Specification for Thin-Gauge Nonoriented ElectricalSteel Fully Processed Types3.Terminology3.1 Definitions:Except as defined as follows,the symbolsand terminology used in this test method are defined inTerminology A340.3.1.1 edge taper and crownthe variations of thick
10、nessacross the widths of cold-rolled steel coils,that is,perpendicu-lar to the rolling direction.Edge taper and crown are not thesame as thickness variation.Thickness variation is measuredparallel to the rolling direction(although it is loosely defined asvariation in any direction).See Fig.1.3.1.1.1
11、 crownthe variation of thickness from the edge tothe center,perpendicular to the rolling direction.3.1.1.2 edge taperthe variation of thickness from the edgeto approximately 4 in.100 mm from the edge of the coil.3.1.1.3 edge taper gamma()the slope of the edge taper(adimensionless number)expressed in
12、 ten thousandths of a unitper unit.3.1.2 edge trimmingthe slitting of a narrow strip fromeach edge of the master coil for discard.This reduces the edgetaper gamma on the remainder of the coil.3.1.3 gamma stripa 1 to 4 in.25 to 102 mm strip cutacross the full width of the master coil(or master coil c
13、oupon),for the purpose of measuring edge taper and crown.3.1.4 master coilsfull-width coils as produced by cold-rolling mills.Slit coils are narrower width coils slit from a1This test method is under the jurisdiction of ASTM Committee A06 onMagnetic Properties and is the direct responsibility of Sub
14、committee A06.01 on TestMethods.Current edition approved Oct.1,2017.Published November 2017.Originallyapproved in 1997.Last previous edition approved in 2010 as A971/A971M 10.DOI:10.1520/A0971_A0971M-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Servic
15、e at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocke
16、n,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 master coil.A master coil coupon is a full-width piece of themaster coil,usually manually cut off for test purposes.4.Summary of Test Method4.1 In determin
