1、Designation:B66490(Reapproved 2012)Standard Specification for80%Silver-20%Graphite Sliding Contact Material1This standard is issued under the fixed designation B664;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last rev
2、ision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification defines the criteria for compositionand other requirements for brushes with a nominal silvercontent of 80%,by we
3、ight,with the balance being substan-tially graphite.1.2 The values stated in inch-pound units are to be regardedas standard.No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is therespo
4、nsibility of the user of this standard to become familiarwill all hazards including those identified in the appropriateMaterial Safety Data Sheet(MSDS)for this product/materialas provided by the manufacturer,to establish appropriatesafety and health practices,and determine the applicability ofregula
5、tory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2B613 Guide for Preparing Specifications for MiniatureBrushes of Composite Materials for Sliding ElectricContactsE18 Test Methods for Rockwell Hardness of Metallic Ma-terials2.2 ANSI Standard:C64.1 Brushes for Electrical Machines
6、33.Requirements3.1 Chemical Composition,shall be as follows:Silver80 3%(weight)GraphitebalanceTotal metal impurities1%maxPercent ash in graphite(ANSI C64.1)5%max3.2 Physical PropertiesThe following lot average proper-ties must be met.Unless otherwise agreed between the pro-ducer and the user,the num
7、ber of samples shall be five.3.2.1 DensityThe minimum acceptable density shall be5.15 g/cm3as determined by the measurement and weightmethod defined by ANSI C64.1.3.2.2 Shear Strength:3.2.2.1 The shear strength for the normal and transversedirections shall be measured for rectangular parallelepipeds
8、and shall be 2000 psi(14 MPa),minimum.3.2.2.2 The shear strength for the longitudinal shear direc-tion shall be measured for cylinders and shall be 1000 psi(6.9MPa),minimum.3.3 MicrostructureParts shall be visually free of structuraldefects,cracks,etc.,upon examination at 50.The pressdirection,as ev
9、idenced by laminations,shall be as defined bythe purchase order.Also the brush material shall not containabrasive particles that will sliver a metal alloy ring with ahardness$110 HK100when the brush force is equal to 30 g orthat necessary for 5.0 psi(34 kPa)pressure,whichever isgreater.A sliver is d
10、efined as a loose wear particle with onedimension$50 the next smaller dimension.Although sliver-ing can be caused by coarse abrasive particles,other param-eters can contribute to slivering(for example,very high brushforce).3.4 Source or grade of raw materials(for example,graphite)or methods of manuf
11、acture shall not be changed withoutnotifying users.4.Reference Properties4.1 Because of their size,the following properties forminiature brushes cannot always be determined;however,these properties are typical for larger parts.4.1.1 Superficial HardnessThe typical Rockwell superfi-cial hardness for
12、this material is 44 R15W as determined byTest Method E18 with a18-in.steel ball.4.1.2 Specific ResistanceThe typical specific resistancefor the material is 4 106V-in.(1 107V-m)as determinedby the method detailed in ANSI C64.1.5.Certification5.1 Material supplied under this specification shall be cer
13、-tified as meeting the requirements of this specification by theproducer of the material.1This specification is under the jurisdiction of ASTM Committee B02 onNonferrous Metals and Alloys and is the direct responsibility of SubcommitteeB02.05 on Precious Metals and Electrical Contact Materials.Curre
14、nt edition approved May 1,2012.Published May 2012.Originallyapproved in 1979.Last previous edition approved in 2006 as B664 81(2006).DOI:10.1520/B0664-90R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMSt
15、andards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 1942
16、8-2959.United States1 6.Keywords6.1 electrical contacts;graphite;silver;sliding contactsASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard.Users of this standard are expressly advised that determination of the validity of any such patent rights,and the riskof infringement of such rights,are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical co
