1、Designation:C1127/C1127M15Standard Guide forUse of High Solids Content,Cold Liquid-AppliedElastomeric Waterproofing Membrane with an IntegralWearing Surface1This standard is issued under the fixed designation C1127/C1127M;the number immediately following the designation indicates the yearof original
2、 adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This guide describes the design and installation of coldliquid-applied el
3、astomeric waterproofing membrane systemsthat have an integral wearing surface.The cold liquid-appliedelastomeric waterproofing membrane(membrane)to whichthis guide refers is specified in Specification C957.1.2 Concrete Slab-on-GradeWaterproofing the upper sur-face of a concrete slab on grade present
4、s special problems dueto the possibility of negative hydrostatic pressure causing lossof bond to the substrate.Consideration of these problems isbeyond the scope of this guide.Consult the membrane manu-facturer for recommendations when this situation exists.1.3 The committee having jurisdiction for
5、this guide is notaware of any similar ISO standard.1.4 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The values stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the
6、 two systems may result in non-conformancewith the standard.1.5 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bili
7、ty of regulatory limitations prior to use.For specific hazardstatements see 15.4.2.Referenced Documents2.1 ASTM Standards:2C33 Specification for Concrete AggregatesC150 Specification for Portland CementC330 Specification for Lightweight Aggregates for Struc-tural ConcreteC332 Specification for Light
8、weight Aggregates for Insulat-ing ConcreteC717 Terminology of Building Seals and SealantsC755 Practice for Selection of Water Vapor Retarders forThermal InsulationC920 Specification for Elastomeric Joint SealantsC957 Specification for High-Solids Content,Cold Liquid-Applied Elastomeric Waterproofing
9、 Membrane With Inte-gral Wearing SurfaceC962 Standards Guide for Use of Elastomeric Joint Sealants(Withdrawn 1992)3C1193 Guide for Use of Joint SealantsD653 Terminology Relating to Soil,Rock,and ContainedFluidsD1079 Terminology Relating to Roofing and WaterproofingD1752 Specification for Preformed S
10、ponge Rubber Corkand Recycled PVC Expansion Joint Fillers for ConcretePaving and Structural ConstructionD2628 Specification for Preformed Polychloroprene Elasto-meric Joint Seals for Concrete Pavements2.2 U.S.Department of Commerce Standard:Product Standard PS 1-74 Construction and Industrial Ply-wo
11、od42.3 American Concrete Institute(ACI)Standard:301-84(1985)Specification for Structural Concrete forBuildings52.4 Steel Structures Painting Council(SSPC)Standards:Steel Structures Painting Manual,Systems and Specifica-tions:Specification SSPC SP-2 Wire Brush Cleaning61This guide is under the jurisd
12、iction of ASTM Committee D08 on Roofing andWaterproofing and is the direct responsibility of Subcommittee D08.25 on LiquidApplied Polymeric Materials Used for Roofing and Waterproofing Membranes thatare Directly Exposed to the Weather.Current edition approved Jan.1,2015.Published February 2015.Origi
13、nallyapproved in 1989.Last previous edition approved in 2009 as C1127 01(2009).DOI:10.1520/C1127_C1127M-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards
14、Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from National Institute of Standards and Technology(NIST),100Bureau Dr.,Stop 1070,Gaithersburg,MD 20899-1070,http:/www.nist.gov.5Available from American Concrete In
15、stitute(ACI),P.O.Box 9094,FarmingtonHills,MI 48333-9094,http:/www.concrete.org.6Available from Society for Protective Coatings(SSPC),40 24th St.,6th Floor,Pittsburgh,PA 15222-4656,http:/www.sspc.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United
16、 States1 Specification SSPC SP-6 Commercial Blast Cleaning62.5 American Plywood Association(APA)Standard:APA Plywood Construction Guide73.Terminology3.1 DefinitionsRefer to Terminology D1079.3.2 Definitions of Terms Specific to This Standard:3.2.1 cold-appliedcapable of being applied without heat-ing as contrasted to hot-applied.3.2.1.1 DiscussionCold-applied products are furnished ina liquid state,whereas hot-applied products are furnished assolids that must be heated to liquefy them.3.2.2 curi
