1、Designation:F131798(Reapproved 2012)Standard Test Method forCalibration of Microwave Ovens1This standard is issued under the fixed designation F1317;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number i
2、n parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is applicable to microwave ovensdesigned for both home and commercial use.It was developedfor use in the evaluation of volatile an
3、d nonvolatile compo-nents of microwave susceptor packages.1.2 This test method was collaboratively evaluated withmicrowave ovens with nominal output ratings of 700 W.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the
4、user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodF874 Test Meth
5、od for Temperature Measurement and Pro-filing for Microwave SusceptorsF1308 Test Method for Quantitating Volatile Extractables inMicrowave Susceptors Used for Food ProductsF1349 Test Method for Nonvolatile Ultraviolet(UV)Ab-sorbing Extractables from Microwave SusceptorsF1500 Test Method for Quantita
6、ting Non-UV-AbsorbingNonvolatile Extractables from Microwave Susceptors Uti-lizing Solvents as Food SimulantsF1519 Test Method for Qualitative Analysis of VolatileExtractables in Microwave Susceptors Used to Heat FoodProducts3.Apparatus and Reagents3.1 Microwave Oven,as manufactured.3.2 Beakers,2 L.
7、(Alternatively use a 2-L polystyrene foamcontainer.)3.3 Thermometer,readable to 60.5C.3.4 Stopwatch.4.Procedure4.1 Using the stopwatch,check the accuracy of the micro-wave oven timer.Timer should be accurate to within 2%.Ifnot,determine the settings necessary to ensure accuracy.4.2 Fill a 2 L beaker
8、 with exactly 1000 mL of distilled waterat 18 to 20C.Record initial temperature of the water as T1.4.3 Remove the thermometer and place the beaker in thecenter of the microwave oven.If the oven has been usedrecently,allow it to cool until it is at room temperature.4.4 Microwave at full power for 2 m
9、in 3 s.The additional 3s is to allow for the magnetron start up delay.4.5 Immediately after the power cycle completion,immersethe thermometer in the water and vigorously stir.Measure thetemperature of the water.Record this temperature as T2.4.6 Repeat the measurements to obtain triplicate measure-me
10、nts of the temperature rise.4.7 Once calibrated,this oven can be used for analytical teststandards such as Test Methods F874,F1308,F1349,F1500,and F1519.4.8 Recalibrate oven daily.5.Calculation5.1 Calculate the output,O,of the microwave oven in wattsusing the following formula:O 5 34.9T22 T1!where:T
11、1=initial temperature of the water,C,andT2=final temperature of the water,C.5.2 Average the three output values and use this mean as thecalibrated output wattage of the microwave oven.6.Report6.1 Report the following information:6.1.1 Mean and standard deviation of these values foroutput wattage of
12、the microwave oven.1This test method is under the jurisdiction ofASTM Committee F02 on FlexibleBarrier Packaging and is the direct responsibility of Subcommittee F02.15 onChemical/Safety Properties.Current edition approved Nov.1,2012.Published November 2012.Originallyapproved in 1990.Last previous e
13、dition approved in 2007 as F1317 98(2007).DOI:10.1520/F1317-98R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.
14、Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 7.Precision and Bias7.1 Seven laboratories participated in the collaborativestudy,each using a microwave oven with a rated output of 700W.From the data submitted,the mean output calculated w
15、as686 W,with a within-lab coefficient of variation of 2.1%,abetween-lab coefficient of variation of 5.9%and an overallcoefficient of variation of 6.3%.The data are shown in Table1 which is based on a round robin test conducted in 1989.Eachlaboratory provided their own ovens.Each test result was thet
16、est value of an individual determination.Each laboratoryobtained three test results for their oven.(WarningThefollowing explanations of RSrand RSR(7.2-7.2.2)are onlyintended to present a meaningful way of considering theapproximate precision of this test method.The data in Table 1should not be rigorously applied to acceptance or rejection ofmicrowave ovens,as those data are specific to the round robinand may not be representative of other conditions.Users of thistest method should apply the prin
