1、Designation:F117301(Reapproved 2012)An American National StandardStandard Specification forThermosetting Resin Fiberglass Pipe Systems to Be Usedfor Marine Applications1This standard is issued under the fixed designation F1173;the number immediately following the designation indicates the year ofori
2、ginal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers reinforced thermosetting resinpipe systems
3、with nominal pipe sizes(NPS)1 through 48 in.(25 through 1200 mm)which are to be used for all fluidsapproved by the authority having jurisdiction in marine pipingsystems.1.2 The dimensionless designator NPS has been substitutedfor traditional terms as“nominal diameter,”“size,”and“nomi-nal size.”1.3 V
4、alues stated in inch-pound are to be regarded as thestandard.Values given in parentheses are for information only.1.4 The following safety hazards caveat pertains to the testmethods which are included in this specification.This standarddoes not purport to address all of the safety concerns,if any,as
5、sociated with its use.It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1598 Test Method for Ti
6、me-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD2105 Test Method for Longitudinal Tensile Properties of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)Pipe and TubeD2310 Classifi
7、cation for Machine-Made“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD2584 Test Method for Ignition Loss of Cured ReinforcedResinsD2924 Test Method for External Pressure Resistance of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD2992 Practice for Obtaining Hydrostatic or
8、 Pressure De-sign Basis for“Fiberglass”(Glass-Fiber-ReinforcedThermosetting-Resin)Pipe and FittingsD3567 Practice for Determining Dimensions of“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)Pipe andFittingsD5028 Test Method for Curing Properties of PultrusionResins by Thermal AnalysisD5686
9、Specificationfor“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)Pipe and Pipe Fittings,Adhesive Bonded Joint Type Epoxy Resin,for Conden-sate Return Lines(Withdrawn 2002)3E1529 Test Methods for Determining Effects of Large Hy-drocarbon Pool Fires on Structural Members and Assem-bliesF412 Ter
10、minology Relating to Plastic Piping Systems2.2 Other Documents:ANSI B16.1 Cast Iron Pipe Flanges and Flanged Fittings4ANSI B16.5 Pipe Flanges and Flanged Fittings4IMO ResolutionA.753(18)Guidelines for theApplication ofPlastic Pipes on Ships5NSF-616CodeofFederalRegulations 21CFR175.105,21CFR177.2280,
11、21CFR177.2410,and 21CFR177.24205Code of Federal Regulations Title 46,Part 56,for PipingSystems,and Subpart 56.60-25 for Nonmetallic Materials5IMO Resolution A.653(16)Recommendation on ImprovedFire Test Procedures for Surface Flammability ofBulkhead,Ceiling,and Deck Finish Materials51This specificati
12、on is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition approved Dec.15,2012.Published December 2012.Originallyapproved in 1988.Last previous edition approved in 2006 as F1
13、173 01(2006).DOI:10.1520/F1173-01R12.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The last approved version of
14、 this historical standard is referenced onwww.astm.org.4Available from American National Standards Institute,25 W.43rd St.,4thFloor,New York,NY 10036.5Available from Standardization Documents Order Desk,Bldg.4 Section D,700Robbins Ave.,Philadelphia,PA 19111-5098,Attn:NPODS.6Available from the Nation
15、al Sanitation Foundation,P.O.Box 130140,789 N.Dixboro Rd.,Ann Arbor,MI 48113-0140.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 IMO Resolution MSC.61(67)International Code for Appli-cation of Fire Test Procedures5OTI 95 634 Jet-Fire Res
16、istance Test of Passive Fire Protec-tion Materials72.3 ISO Documents:ISO 9001 Quality Management SystemsRequirements4ISO 75 PlasticsDetermination of Temperature of Deflec-tion Under Load43.Terminology3.1 Definitions are in accordance with Terminologies D883and F412.3.2 Definitions of Terms Specific to This Standard:3.2.1 continuously electrically conductive,advpipe andfittings made conductive using discretely conductive materialsor layers.3.2.2 homogeneously electrically conductive,advpipe andfi