1、Designation:F186014Standard Specification forRubber Sheet Floor Covering With Backing1This standard is issued under the fixed designation F1860;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in par
2、entheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers the requirements for the com-pound and physical characteristics of rubber sheet floor cov-ering having a rubber wear layer wit
3、h backing.Products mayalso contain intermediate layers.1.2 The values stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following precautionary
4、 statement pertains only tothe test method portion,Section 10,of this specification:Thisstandard does not purport to address all the safety concerns,ifany,associated with its use.It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine th
5、e applicability of regulatory limita-tions prior to use.2.Referenced Documents2.1 The following documents if the issue in effect on thedate of the material purchase form a part of this specification tothe extent referenced herein:2.2 ASTM Standards:2D412 Test Methods for Vulcanized Rubber and Thermo
6、plas-tic ElastomersTensionD883 Terminology Relating to PlasticsD1566 Terminology Relating to RubberD2240 Test Method for Rubber PropertyDurometer Hard-nessF141 Terminology Relating to Resilient Floor CoveringsF387 Test Method for Measuring Thickness of ResilientFloor Covering With Foam LayerF410 Tes
7、t Method for Wear Layer Thickness of ResilientFloor Coverings by Optical MeasurementF710 Practice for Preparing Concrete Floors to ReceiveResilient FlooringF925 Test Method for Resistance to Chemicals of ResilientFlooringF970 Test Method for Static Load LimitF1482 Practice for Installation and Prepa
8、ration of PanelType Underlayments to Receive Resilient FlooringF1514 Test Method for Measuring Heat Stability of ResilientFlooring by Color ChangeF1515 Test Method for Measuring Light Stability of Resil-ient Flooring by Color Change2.3 ANSI Standards:ANSI/ASQC Z1.4 Sampling Procedures and Tables for
9、 In-spection by Attributes33.Terminology3.1 DefinitionsFor definitions of other terms used in thisstandard,see Terminology F141.4.Classification4.1 TypesRubber sheet floor covering covered by thisspecification shall conform to the following types:4.1.1 Type IHomogeneous4.1.2 Type IIHeterogeneous4.2
10、GradesRubber sheet floor covering shall be one of thefollowing grades:4.2.1 Grade 1Fibrous backing4.2.2 Grade 2Foamed rubber backing4.3 The above may have either smooth,embossed,ormolded pattern surfaces.4.4 These products shall not contain asbestos.5.Ordering Information5.1 Purchasers shall state w
11、hether this specification is to beused,select the preferred options permitted herein and includethe following information in the invitation to bid or purchaseorder:5.1.1 Title,number,and date of this specification,5.1.2 Type,color,and surface(see Section 4 and Section 6),1This specification is under
12、 the jurisdiction of ASTM Committee F06 onResilient Floor Coveringsand is the direct responsibility of Subcommittee F06.80 onSpecifications.Current edition approved Nov.1,2014.Published December 2014.Originallyapproved in 1998.Last previous edition approved in 2012 as F1860-12.DOI:10.1520/F1860-14.2
13、For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43
14、rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 5.1.3 Quantity,in square feet,square yards,or squaremetres,5.1.4 Thickness required.(see 8.3),5.1.5 Overall thickness,if molded pattern
15、flooring is speci-fied(see 8.1),5.1.6 Width required(see 8.4),5.1.7 Length required(see 8.5),5.1.8 Resistance to chemicals,(see 7.4),5.1.9 Lot information,if other than as specified in AANSI/ASQC Z1.4.(see 10.1 and 11.1),5.1.10 Sampling,if other than as specified in ANSI/ASQCZ1.4(see 10.1 and 11.1),
16、5.1.11 Statement requesting certification,if certification ofcompliance is required(see 12.1),5.1.12 Packing requirements,if other than as specified(see14.1),5.1.13 Palletization,if required,5.1.14 Marking required,if other than specified(see 13.1),and5.1.15 Other requirements.6.Materials and Manufacture6.1 Homogeneous Rubber Sheet Floor CoveringTheproduct shall consist of a wear layer and backing.The surfacecoloring or mottling shall be uniform throughout the entirethickness of the wear layer.T
