1、ERRATAtoASME B47.1-2007Gage BlanksOn page 48,Table 32,decimal range for line 8-T corrected.Lines 9-T and 10-T added.Therevised table is on the following page.THE AMERICAN SOCIETY OF MECHANICAL ENGINEERSThree Park Avenue,New York,NY 10016-5990January 2010M8207ECopyrighted material licensed to Stanfor
2、d University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Copyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consen
3、t of ASME.cTable 32Thread Ring Gages Range No.0 to and Including 434in.;Also Fine-Pitch Instrument Thread Ring Gages,No.0 to and Including No.12(Contd)General DimensionsDecimalNominalRange,URingRingRange,AboveDrill Size,Ream,SPitch DiameterSize AssemblyInclusive,andMNPDrill Size,No.No.No.or in.Inclu
4、dingABCDEFHJKL164164(No.or in.)RMin.Max.SizeMin.Max.VW1-T1No.0 to0.059114.132516532516732532116No.4111640.1370 0.13730.164-360.1400 0.1478 0.0101326(1)0.230(0.0960)(0.1719)(2)2-T2145160.2301381132.5321327163163811321418No.317320.1810 0.18130.216-280.1928 0.19501321160.365(0.1200)(0.2187)3-T338120.36
5、5134716.31636419321415321238316No.2517640.2150 0.21530.250-280.2268 0.22901323320.510(0.1495)(0.2656)4-T4916340.5102316916341116113211634516111617321332732No.721640.2720 0.2723 0.3125-24 0.2854 0.28781163320.825(0.2010)(0.3281)5-T5181180.8252581116151611291611631325167817321332932No.125640.3340 0.33
6、440.375-240.3479 0.35031163321.135(0.2280)(0.3906)6-T61141121.13531434118178273211613163811858716516176429640.3890 0.3894 0.4375-20 0.4050 0.40761163321.510(0.2656)(0.4531)7-T615821.5103341316114238131633217163813858716516176429640.3890 0.3894 0.4375-20 0.4050 0.4076116182.010(0.2656)(0.4531)8-T7218
7、2122.01041278151627811932332134716111161316916716216433640.4510 0.45150.500-200.4675 0.4701332182.510(0.3281)(0.5156)9-T725832.51057813833823322716115161316916716216433640.4510 0.45150.500-200.4675 0.4701332183.010(0.3281)(0.5156)10-T73183123.010512151617163782716332273271623161316916716216433640.45
8、10 0.45150.500-200.4675 0.4701332183.510(0.3281)(0.5156)11-T835843.51063815161124582151633225812291613458133241640.5710 0.57150.625-180.5889 0.5919332184.010(0.4062)(0.6406)12-T84184344.0107141112538338332313212313458133241640.5710 0.57150.625180.5880 0.5919332184.760(0.4062)(0.6406)GENERAL NOTES:(a
9、)All dimensions are in inches.(b)Thin gage blanks are to be used for all NOT GO thread ring gages.For GO thread ring gages,use thin or thick blanks as follows.Diameter,in.Thin BlankThick BlankFrom No.0 to12,inclusiveAll pitches.Above12to 118,inclusivePitches 12 TPI and finer except91612Pitches coars
10、er than 12 TPIAbove 118Pitches 10 TPI and finerPitches coarser than 10 TPI(c)Screws and sleeves are not shown.(d)Special thicker blanks are sometimes required for checking long lengths of engagement or exceptionally coarse pitch threads.(e)Solid working thread ring gages are of similar standard thic
11、kness and furnished without adjustment feature.Outside diameter of solid ring blanks may be smaller to suit particularrequirements.See Table 39 for solid setting and master thread ring gage blanks.NOTES:(1)Blanks for the range Nos.0 to 12,inclusive,may be either counterbored or milled,as shown in il
12、lustration for Table 32.(2)Approximate.Copyrighted material licensed to Stanford University by Thomson Scientific(),downloaded on Oct-05-2010 by Stanford University User.No further reproduction or distribution is permitted.Uncontrolled when printed.Copyright 2010 by the American Society of Mechanical Engineers.No reproduction may be made of this material without written consent of ASME.c
