收藏 分享(赏)

ASME_FAP-1-1995.pdf

上传人:益****师 文档编号:167928 上传时间:2023-03-03 格式:PDF 页数:34 大小:5.38MB
下载 相关 举报
ASME_FAP-1-1995.pdf_第1页
第1页 / 共34页
ASME_FAP-1-1995.pdf_第2页
第2页 / 共34页
ASME_FAP-1-1995.pdf_第3页
第3页 / 共34页
ASME_FAP-1-1995.pdf_第4页
第4页 / 共34页
ASME_FAP-1-1995.pdf_第5页
第5页 / 共34页
ASME_FAP-1-1995.pdf_第6页
第6页 / 共34页
亲,该文档总共34页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、STD.ASME FAP-1-ENGL399507596700579897958ASME FAP-1-1995(REVISION OF ASME FAP-1-1990)Quality Assurance ProgramRequirements for FastenerManufacturers,Distributors,and Testing LaboratoriesAN ASME STANDARDThe American Society ofMechanical EngineersCopyright by the American Society Of Mechanical Engineer

2、sSTD.ASME FAP-1-ENGL199507596700579899720Date of Issuance:August 18,1995The current edition of ASME FAP-1 supersedes the 1990 edition of thisStandard.This Standard was approved by the Board on Standardization onJuly 11,1995.The 1995 edition of this Standard is being issued with an au-tomatic addenda

3、 subscription service.The use of an addenda allows revisionsmade in response to public review comments or committee actions to bepublished on a regular basis.ASME is the registered trademark of the American Society of Mechanical Engineers.This code or standard was developed under procedures accredit

4、ed as meeting the criteria forASME Standards.The Consensus Committee that approved the code or standard was balancedto assure that individuals from competent and concerned interests have had an opportunity toparticipate.The proposed code or standard was made available for public review and commentwh

5、ich provides an opportunity for additional public input from industry.academia,regulatoryagencies,and the public-at-large.ASME does not approve,rate,or endorseany item,construction,proprietary device.oractivity.ASME does not take any position with respect to the validity of any patent rights asserte

6、d inconnection with any items mentioned in this document,and does not undertake to insure anyoneutilizing a standard against liability for infringement of any applicable Lotters Patent,nor assumeany such liability.Users of a code or standard are expressly advised that determination of thevalidity of

7、 any such patent rights,and the risk of infringement of such rights,is entirely their ownresponsibility.Participation by federal agency representative(s)or person(s)aftiliated with industry is not tobe interpreted as government or industry endorsement of this code or standard.ASME accepts responsibi

8、lity for only those interpretations issued in accordance with governingASME procedures and policies which preclude the issuance of interpretations by individualvolunteers.No part of this document may be reproduced in any form.in an eiectronic retrieval system or otherwise,without the prior written p

9、ermission of the publisher.Copyright 1995 byTHE AMERICAN SUCIEIY UF MECHANICAL ENGINEERSAll Rights ReservedPrinted in U.S.A.STD.ASME FAP-1-ENGL1995=0759b700579900272ASME COMMITTEE B18Standardization of Boits,Nuts,Rivets Screws,Washers,and Similar Fasteners(The following is a roster of the Committee

10、at the time of approval of this Standard)OFFICERSK.E.McCullough,ChairD.A.Clever,Vice ChairE.Schwartz,Vice ChairA.M.Nickles,SecretaryCOMMITTEE PERSONNELJ.C.AkinsA.HerskovitzR.M.SerabinJ.BelfordA.C.HoodR.D.StrongD.J.BroomfieldF.W.KernE.SchwartzJ.A.BudaW.H.KopkeJ.F.SullivanR.M.ByrneP.D.KorsmoR.L.Tennis

11、D.A.Clever.I G I angensteinS.W.VassA.P.CockmanM.LevinsonR.G.WeberA.C.DicolaJ.B.LovyC.J.WilsonB.A.DusinaK.E.McCulloughR.R WrightH.W.EllisionD.J.MileyJ.G.ZeratskyG.A.GobbM.D.PrasadR.J.Harringtonw.ScheveyB18 SUBCOMMITTEE 28:FASTENER CRITERIA ACCREDITATIONOFFICERSC.J.Wilson,Acting ChairJ.D.Smith,Vice Ch

12、airS.M.Wunsch,SecretaryCOMMITTEE PERSONNELJ.BelfordJ.G.LangensteinJ.A.BudaK.E.McCulloughR.ByrneR.S.PiotrowskiA.HerskovitzH.E.Schock,Jr.W.KaarlelaL.C.SchrocderW.H.KopkeJ.D.SmithG.S.KorinJ.F.SullivanP D.KorsmoC.B.WackrowC.J.WilsonSTD.ASME FAP-1-ENGL199507596700579901109CONTENTSStandards Committee Rost

13、eriiPart 1-Introduction1.1.0SC0pe1.2.0Definitions.1Part 2-Manufacturers and Alteration Distributors2-1.0Evidence of Management Responsibility.2.1.1Quality Commitment9+t9。442-1.2Fiscal Responsibility.52-1.3Training Responsibility.2-2.0Inquiry/Qu0 tation.52-2.1Prior Review.52-2.2Review Interaction52-2

14、.3Written Procedure52-2.4Ongoing Review.J2.3.0Engineering52-3.1Specification Requirements52-3.2Drawing Requirements.52-3.3Supplier Evaluation:Sub-Tier52-3.4Design Change/Configuration Control.52-4.02-4.1Procurement.6Responsibilities of Procurement.62-4.2Procedures for Procurement.62-4.2.1Technical Requirements.62.4.2.2Source Approvals and Controls.62.5.0Production62.51Production Responsibilities.62-5.2Production and Planning Elements.62.5.2.1Capacity62-5.2.2Equipment Capahility62-5.2.3Tooling.62-5.2.4Equipment Operators.62-5.2.5Repair and Maintenance.6

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2