1、Designation:E10317Standard Practice forRapid Indentation Hardness Testing of Metallic Materials1This standard is issued under the fixed designation E103;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A numb
2、er in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This practice covers a procedure for rapid indentationhardness testing of metallic materials.1.2 This practice includes additional requirement
3、s in AnnexA1 for the direct,indirect,and daily verification of rapidindentation hardness testing machines.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns
4、,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recogni
5、zed principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2E10 Test Method for Brinell
6、 Hardness of Metallic MaterialsE74 Practice of Calibration of Force-Measuring Instrumentsfor Verifying the Force Indication of Testing Machines2.2ISO Standards:3ISO 17025 General requirements for the competence oftesting and calibration laboratoriesISO/IEC 17011 Conformity assessment-General require
7、-ments for accreditation bodies accrediting conformityassessment bodies3.Terminology3.1 Definitions:3.1.1 calibrationdetermination of the values of the sig-nificant parameters by comparison with values indicated by areference instrument or by a set of reference standards.3.1.2 rapid indentation hard
8、ness testan indentation hard-ness test using calibrated machines to force a tungsten carbideball,under specified conditions,into the surface of the materialunder test and to measure the depth of the indentation.Thedepth measured can be from the surface of the test specimen orfrom a reference positio
9、n established by the application of apreliminary test force.The depth measurement is usuallycorrelated to another scale or Brinell hardness number.3.1.3 verificationchecking or testing to assure confor-mance with the specification.4.Significance and Use4.1 This practice is used when it is desired to
10、 make Brinelltype hardness tests very rapidly on a high volume of samples,as in the inspection of the output of a heat-treating furnace.4.2 This practice requires the measurement of indentationdepth and eliminates the need to measure the diameter of theindent optically as required in a Brinell hardn
11、ess test.4.3 This practice is not a standard Brinell hardness testmethod and does not meet the requirements of Test MethodE10.4.4 Since the test forces and method of display of the depthmeasurement differ between manufacturers of rapid indenta-tion hardness testing equipment,the test results from eq
12、uip-ment from different manufacturers are not comparable.5.Apparatus5.1 Testing MachineEquipment for rapid indentationhardness testing usually consists of a testing machine,whichsupports the test specimen and applies an indenting force(s)toa ball in contact with the specimen,and a system for measuri
13、ngand displaying an indication of the depth of the indentation.The test force can be applied either as a single total test forcewhereby the depth is measured usually from the surface of thetest specimen or as a preliminary and total test force wherebythe depth is measured as the increase from the pr
14、eliminary tothe total test force.1This test method is under the jurisdiction of ASTM Committee E28 onMechanical Testing and is the direct responsibility of Subcommittee E28.06 onIndentation Hardness Testing.Current edition approved April 1,2017.Published May 2017.Originallypublished as E103 84.Last
15、previous edition approved in 2012 as E103 12.DOI:10.1520/E0103-17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.
16、3Available from International Organization for Standardization(ISO),1,ch.dela Voie-Creuse,CP 56,CH-1211 Geneva 20,Switzerland,http:/www.iso.org.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of I
