1、Designation:E2134/E2134M14Standard Test Method forEvaluating the Tensile-Adhesion Performance of an ExteriorInsulation and Finish System(EIFS)1This standard is issued under the fixed designation E2134/E2134M;the number immediately following the designation indicates the yearof original adoption or,i
2、n the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method evaluates the tensile-adhesion perfor-mance of an exterior insulation
3、and finish System(EIFS)or itsindividual components by two different procedures:ProcedureA,Dry Conditioning and Testing of Specimens;and ProcedureB,Wet Conditioning and Testing of Specimens.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard.The value
4、s stated ineach system may not be exact equivalents;therefore,eachsystem shall be used independently of the other.Combiningvalues from the two systems may result in non-conformancewith the standard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use
5、.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2E4 Practices for Force Verification of Testing MachinesE631 Terminology of Bui
6、lding ConstructionsE2110 Terminology for Exterior Insulation and Finish Sys-tems(EIFS)2.2 EIFS Industry Members Association(EIMA):3Guideline Specification for Exterior Insulation and FinishSystems,Class PB3.Terminology3.1 Definitions:3.1.1 For general terminology regarding EIFS and buildingin genera
7、l,see Terminology E2110(for EIFS terms)andTerminology E631(for buildings in general).3.2 Definitions of Terms Specific to This Standard:3.2.1 adhesionthe state in which two surfaces are heldtogether by forces at the interface.3.2.2 cohesionthe molecular attraction that holds a bodytogether.The inter
8、nal strength of a material.3.2.3 specimenthe entire assembled unit cut from thesample and submitted for test as described in Section 7.3.2.4 tensile-adhesion strengththe ultimate strength intension normal to the plane of the system.4.Summary of Test Method4.1 Specimens are tested by applying tensile
9、 loads normal tothe plane of the system in a controlled environment todetermine the tensile adhesion of the system or individualcomponents of the system,of both.5.Significance and Use5.1 Maintenance of adequate tensile adhesion of EIFScomponents to each other,and to the substrate are essential forlo
10、ng term performance of the system.5.2 The tensile-adhesion properties obtained by this testmethod are not purported to be representative of wind load orother structural and moisture related properties of the EIFSwall assembly.Tensile-adhesion properties using this testmethod are used as one of the f
11、actors in evaluating substratesand to compare adhesives.6.Apparatus6.1 Tensile Test Machine,capable of producing a tensileload on the test specimen at a constant cross-head rate of 1.5mm/min 0.05 in./min.6.2 Load Measuring Device,calibrated according to Prac-tice E4,the test machine load measuring d
12、evice shall becapable of measuring the load to an accuracy of 61%of themaximum load applied to the test specimen.6.3 Loading FixturesThe loading fixtures shall be self-aligning and shall not apply eccentric loads.The loading1This test method is under the jurisdiction of ASTM Committee E06 onPerforma
13、nce of Buildings and is the direct responsibility of Subcommittee E06.58on Exterior Insulation and Finish Systems(EIFS).Current edition approved April 1,2014.Published May 2014.Originallyapproved in 1998 as PS 72 98.Last previous edition approved in 2006 asE2134 01(2006).DOI:10.1520/E2134_E2134M-14.
14、2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from EIFS Industry Members Association(EIMA),513 West B
15、roadStreet,Suite 210,Falls Church,VA 22046-3257,http:/.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 fixtures shall be a minimum of 12.0-mm 0.5-in.-thick metalblocks to keep the bonded facings essentially flat under themaximum applied l
16、oad.The size of the loading blocks shall benot less than the bonded area of the test specimen.6.4 Temperature Control ChamberA room or chambercapable of maintaining 23 6 3C 75 6 5F and 50 6 5%relative humidity.6.5 Containers,corrosion resistant containers of sufficientsize to hold specimens.7.Sample Preparation7.1 Prepare one sample for each test condition described inSections 9,10,and 11.Samples shall be not less than 150 by200 mm 6 by 8 in.in size,such that,six test specimens nosmaller than 50
