1、Designation:E207214An American National StandardStandard Specification forPhotoluminescent(Phosphorescent)Safety Markings1This standard is issued under the fixed designation E2072;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the y
2、ear of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers minim
3、um performance re-quirements for newly applied photoluminescent(phosphores-cent)safety materials used to provide supplemental markingsof escape routes,emergency equipment,and obstructions alongthe escape route.(see also Test Method E2073 and GuideE2030).1.2 This specification establishes minimum lum
4、inance val-ues for photoluminescent(phosphorescent)markings.1.3 This specification applies to all types of photolumines-cent(phosphorescent)markings,including but not limited toplastics,coatings,ceramics,films,etc.1.4 This specification does not cover potentially diminishedperformance due to wear an
5、d tear and aging.1.5 This specification applies only to photoluminescent(phosphorescent)markings emitting the majority of spectralenergy within the 515 to 535 nanometer range.1.6 When reference is made regarding photoluminescencein the text of this standard,it implies phosphorescence.1.7 The values
6、stated in inch-pound units are to be regardedas standard.The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.2.Referenced Documents2.1 ASTM Standards:2E284 Terminology of AppearanceE1316 Terminology for Nondest
7、ructive ExaminationsE2030 Guide for Recommended Uses of Photoluminescent(Phosphorescent)Safety MarkingsE2073 Test Method for Photopic Luminance of Photolumi-nescent(Phosphorescent)Markings3.Terminology3.1 Definitions of terms in Terminology E284 and Termi-nology E1316 are applicable to this specific
8、ation.4.Performance Requirements4.1 Optical Requirements:4.1.1 Luminance in a Test LaboratoryThe photopic lumi-nance of all three specimens of the photoluminescent marking,measured in compliance with Test Method E2073,shall be notless than:30 mcd/m2at 10 min after activation has ceased;and5 mcd/m2at
9、 90 min after activation has ceased.4.2 Walking Surfaces Materials:4.2.1 Photoluminescent safety markings intended to beinstalled on walking surfaces of the means of egress shall havea slip-resistant surface and be securely attached.5.Installation Site5.1 On-Site LuminanceThe photopic luminance of o
10、n-siteinstalled photoluminescent markings shall be measured incompliance with Test Method E2073.The on-site lighting shallbe used as activation.Markings must be a minimum of 1-in.(25.4-mm)width.The required photopic luminance shall,at alltimes,be not less than:30 mcd/m2at 10 min after activation has
11、 ceased;and 5 mcd/m2at 90 min after activation has ceased.5.2 ActivationThe required recharging activation level forphotoluminescent safety markings depends on the ambientluminance level,the type of light source utilized,and theduration of exposure to the activating light source.Consultmanufacturers
12、 for performance levels under various lightingconditions.6.Installation Instructions6.1 When this standard is used to show compliance withcodes or standards,installation instructions shall be provided.6.1.1 The installation instructions shall outline:1This specification is under the jurisdiction of
13、ASTM Committee E12 on Colorand Appearance and is the direct responsibility of Subcommittee E12.13 onPhotoluminescent Safety Markings.Current edition approved Aug.1,2014.Published August 2014.Originallyapproved in 2000.Last previous edition approved in 2010 as E2072 10.DOI:101520/E2072-14.2For refere
14、nced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohoc
15、ken,PA 19428-2959.United States1(1)Information on installation surface treatments neces-sary prior to installation;(2)That a floor surface material successfully passed theSlip Resistance Test;(3)Mounting instructions;(4)The amount of activating light for proper activation andthe type of light the pr
16、oduct was tested in accordance with TestMethod E2073;(5)A warning that should any changes in activating light-ing occur,to ensure that sufficient activation is still guaranteed;(6)Maintenance instructions;(7)Periodic inspection procedures,especially if marking isintended for use in compliance with applicable local or nationalmodel codes,to ensure compliant activation by proper ambientlighting.7.Keywords7.1 escape routes;luminance;photoluminescent safetymarkingsAPPENDIXES(Nonmandatory Information
