1、Designation:D638599(Reapproved 2017)Standard Test Method forDetermining Acid-Extractable Content in Activated Carbonby Ashing1This standard is issued under the fixed designation D6385;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,t
2、he year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method is to be used for determination of theacid-extractable content of a sample of activated carbon.
3、Thistest method presupposes the existence of substances other thancarbon to be present with activated carbon but does not purportto address or identify those substances which may be present.This test method should be applicable to any form in whichactivated carbon may exist and requires the performa
4、nce ofTest Method D2866.1.2 This test method requires the use of concentratedhydrochloric acid,which should be used in an appropriate andsafe manner,with eye protection,skin protection,and handlingcarried out in a properly operating fume hood.The proper useof a muffle furnace is addressed in Test Me
5、thod D2866.1.3 The values stated in SI units are to be regarded asstandard.No other units of measurement are included in thisstandard.1.4 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establi
6、sh appro-priate safety and health practices and determines the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:2D1193 Specification for Reagent WaterD2866 Test Method for Total Ash Content of ActivatedCarbonD2867 Test Methods for Moisture in Activated C
7、arbonE300 Practice for Sampling Industrial Chemicals3.Summary of Test Method3.1 The percent acid-extractable content of an activatedcarbon sample is determined by the difference between thepercent mass of total ash of a sample and the percent mass oftotal ash of a sample which has been acid extracte
8、d.4.Significance and Use4.1 The quantitative determination of acid-extractable con-tent is useful in evaluating activated carbon samples thatcontain acid-soluble impurities.These acid-soluble impuritiescan affect applications of activated carbon.4.2 Limitations of MethodHydrochloric acid is used int
9、his test method as the extracting acid.All elements orcompounds present in the activated carbon sample,which canbe acid extracted,are assumed to form water-soluble chloridesalts.Hydrochloric acid may not solubilize all impurities ofactivated carbon.5.Apparatus5.1 250-mL Glass Beakers,for boiling and
10、 drying thesample.5.2 Watch Glass,suitable for 250-mL beaker.5.3 Graduated Cylinders,of 100-mL(TD)and 25-mL(TD)size.5.4 Buchner Vacuum Funnel,7-cm ID or equivalent filteringdevice.5.5 Vacuum Filter Flask,with side arm,500 mL.5.6 Vacuum Filter Collar,for the above filter flask.5.7 Filter Paper,which
11、is hardened,ashless paper,8micron pore size and 7 cm in diameter is recommended,or adiameter which matches the vacuum funnel.The paper will beashed with the carbon,so ashless paper is necessary.5.8 Drying Oven,maintained at 150 C 6 5 C.5.9 Muffle Furnace,as specified in Test Method D2866.5.10 Porcel
12、ain Crucibles,as specified in Test MethodD2866.5.11 Desicator,containing indicating silica gel or any otherdesicant,which is effective in maintaining dryness of coolinghot crucibles or oven dried carbon samples.5.12 Balance,capable of measurement of 0.1 mg.1This test method is under the jurisdiction
13、 of ASTM Committee D28 on LiquidPhase Evaluation.Current edition approved March 1,2017.Published March 2017.Originallyapproved in 1999.Last previous edition approved in 2011 as D6385 99(2011).DOI:10.1520/D6385-99R17.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Cu
14、stomer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed
15、in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.13 Carbon Particle Size
16、Reduction,a mortar and pestle,orany other means of systematically reducing activated carbonparticle size to pass through a No.325 U.S.mesh screen.Thesize reduction device must be constructed of material that willnot contaminate the carbon sample with acid-soluble materials.5.14 No.325 U.S.Mesh Screen,for sieving the sample aftersize reduction.6.Reagents6.1 Concentrated Hydrochloric Acid,ACS reagent grade isrecommended,37%HC1 w/w 6 2%.6.2 ASTM Type II Water,or better is recommended for lowresidue
