1、Designation:D62307(Reapproved 2019)1Standard Test Methods forRubber PropertyHeat Generation and Flexing Fatigue InCompression1This standard is issued under the fixed designation D623;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,th
2、e year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1NOTECorrected 2.2 editorially in March 2021.1.Scope1.1 These test methods may be used to compare the fatiguecharacteristics
3、 and rate of heat generation of different rubbervulcanizates when they are subjected to dynamic compressivestrains.1.2 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafet
4、y concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with
5、 internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D39
6、5 Test Methods for Rubber PropertyCompression SetD1349 Practice for RubberStandard Conditions for Test-ingD3182 Practice for RubberMaterials,Equipment,and Pro-cedures for Mixing Standard Compounds and PreparingStandard Vulcanized SheetsD4483 Practice for Evaluating Precision for Test MethodStandards
7、 in the Rubber and Carbon Black ManufacturingIndustries2.2 ASTM Adjuncts:Goodrich Flexometer Anvil Drawings33.Summary of Test Method3.1 The test consists of subjecting a specimen of rubber ofdefinite size and shape to rapidly oscillating compressivestresses under controlled conditions.Although heat
8、is gener-ated by the imposed oscillating stress,the more convenientparameter,the temperature rise,is measured.The measuredtemperature rise is one of two types:(1)to an equilibriumtemperature or(2)the rise in a fixed time period.Additionalmeasured performance properties are the degree of permanentset
9、 or other specimen dimensional changes,or both,and forcertain test conditions,the time required for a fatigue failure byinternal rupture or blow out.3.2 Two test methods are covered,using the followingdifferent types of apparatus:3.2.1 Test Method AGoodrich Flexometer.3.2.2 Test Method BFirestone Fl
10、exometer.4.Significance and Use4.1 Because of wide variations in service conditions,nocorrelation between these accelerated tests and service perfor-mance is given or implied.However,the test methods yielddata that can be used to estimate relative service quality ofdifferent compounds.They are often
11、 applicable to research anddevelopment studies.5.Preparation of Sample5.1 The sample may consist of any vulcanized rubbercompound except those generally classed as hard rubber,provided it is of sufficient size to permit preparation of the testspecimen required for the test method to be employed.Thes
12、ample may be prepared from a compound mixed experimen-tally in the laboratory or taken from process duringmanufacture,or it may be cut from a finished article ofcommerce.1These test methods are under the jurisdiction of ASTM Committee D11 onRubber and Rubber-like Materials and are the direct respons
13、ibility of SubcommitteeD11.15 on Degradation Tests.Current edition approved Nov.1,2019.Published December 2019.Originallyapproved in 1941.Last previous edition approved in 2014 as D623 07(2014).DOI:10.1520/D0623-07R19E01.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact AS
14、TM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from ASTM International Headquarters.Order Adjunct No.ADJD0623-E-PDF.Original adjunct produced in 1939.Copyright ASTM International,10
15、0 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recomm
16、endations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.15.2 If prepared in the laboratory,the procedure shouldpreferably be essentially as specified in Practice D3182,exceptthat when vulcanization is required,the sample should prefer-ably be molded in block form of sufficient size to permitcutting of the required test specimens rather than in the form ofthe standard test slab.5.2.1 The direct molding of the specimen for Test MethodAis allowed(see 9.4)but may n
