1、Designation:D5473/D5473M20Standard Practice for(Analytical Procedures)Analyzing the Effects of PartialPenetration of Control Well and Determining the Horizontaland Vertical Hydraulic Conductivity in a Nonleaky ConfinedAquifer1This standard is issued under the fixed designation D5473/D5473M;the numbe
2、r immediately following the designation indicates theyear of original adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of lastreapproval.A superscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 This
3、 practice covers an analytical solution for determin-ing the horizontal and vertical hydraulic conductivity of anaquifer by analysis of the response of water levels in theaquifer to the discharge from a well that partially penetrates theaquifer.This standard uses data derived from Test MethodD4050.1
4、.2 LimitationsThe limitations of the technique for deter-mination of the horizontal and vertical hydraulic conductivityof aquifers are primarily related to the correspondence betweenthe field situation and the simplifying assumption of thispractice.1.3 UnitsThe values stated in either SI units or in
5、ch-pound units are to be regarded separately as standard.Thevalues stated in each system may not be exact equivalents;therefore,each system shall be used independently of the other.Combining values from the two systems may result in noncon-formance with the standard.Reporting of test results in unit
6、sother than SI shall not be regarded as nonconformance withthis standard.1.4 All observed and calculated values shall conform to theguidelines for significant digits and rounding established inPractice D6026.1.4.1 The procedures used to specify how data are collected/recorded or calculated,in this s
7、tandard are regarded as theindustry standard.In addition,they are representative of thesignificant digits that generally should be retained.The proce-dures used do not consider material variation,purpose forobtaining the data,special purpose studies,or any consider-ations for the users objectives;an
8、d it is common practice toincrease or reduce significant digits of reported data to becommensurate with these considerations.It is beyond the scopeof this standard to consider significant digits used in analyticalmethods for engineering design1.5 This practice offers a set of instructions for perfor
9、mingone or more specific operations.This document cannot replaceeducation or experience and should be used in conjunction withprofessional judgment.Not all aspects of the practice may beapplicable in all circumstances.This ASTM standard is notintended to represent or replace the standard of care by
10、whichthe adequacy of a given professional service must be judged,nor should this document be applied without the considerationof a projects many unique aspects.The word“Standard”in thetitle of this document means only that the document has beenapproved through he ASTM consensus process.1.6 This stan
11、dard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.7 This internat
12、ional standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committ
13、ee.2.Referenced Documents2.1 ASTM Standards:2D653 Terminology Relating to Soil,Rock,and ContainedFluidsD3740 Practice for Minimum Requirements for AgenciesEngaged in Testing and/or Inspection of Soil and Rock asUsed in Engineering Design and ConstructionD4050 Test Method for(Field Procedure)for With
14、drawaland Injection Well Testing for Determining Hydraulic1This practice is under the jurisdiction of ASTM Committee D18 on Soil andRock and is the direct responsibility of Subcommittee D18.21 on Groundwater andVadose Zone Investigations.Current edition approved June 1,2020.Published June 2020.Origi
15、nallyapproved in 1993.Last previous edition approved in 2015 as D5473/D5473M15.DOI:10.1520/D5473_D5473M20.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards D
16、ocument Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barri
