1、Designation:D558214Standard Test Method forDetermining Formaldehyde Levels from Wood ProductsUsing a Desiccator1This standard is issued under the fixed designation D5582;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of las
2、t revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method covers a small scale procedure formeasuring formaldehyde emission potential from wood prod-ucts under defined
3、 test conditions.The formaldehyde level isdetermined by collecting air-borne formaldehyde in a smalldistilled water reservoir within a closed desiccator.The quan-tity of formaldehyde is determined by a modification of theNational Institute for Occupational Safety and Health(NIOSH)3500 chromotropic a
4、cid test procedure.Other analytical pro-cedures may be used to determine formaldehyde emissionpotential provided that such methods give similar results to thechromotropic acid procedure.However,the test results and testreport must be properly qualified and the analytical procedureemployed must be no
5、ted.Procedures based on acetylacetoneand pararosaniline have been found to give similar results tochromotropic acid in other test methods used in determiningformaldehyde emission potential from wood products(see TestMethod E1333).1.2 Wood products typically evaluated by this test methodare made with
6、 urea-formaldehyde adhesives and includeparticleboard,hardwood,plywood,and medium-density fiber-board.This test method is used for product quality control andis a small bench test method that correlates with the large-scaleacceptance test for determining formaldehyde levels fromwood products,Test Me
7、thod E1333.The general desiccatortesting procedure may be modified for different conditioningtimes to accommodate its use in manufacturing quality control.However,the test results must be properly qualified and theconditioning time employed must be noted.NOTE1If modifications are made to the conditi
8、oning period forquality control purposes,it is important that the modification is consis-tently applied.Otherwise,the results may not be comparable.1.3 The values stated in SI units are to be regarded as thestandard.The values given in parentheses are for informationonly.1.4 This standard does not p
9、urport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.For specific hazardstatements,see Section 6 an
10、d 8.2.5.2.Referenced Documents2.1 ASTM Standards:2E77 Test Method for Inspection and Verification of Ther-mometersE337 Test Method for Measuring Humidity with a Psy-chrometer(the Measurement of Wet-and Dry-Bulb Tem-peratures)E1333 Test Method for Determining Formaldehyde Concen-trations in Air and E
11、mission Rates from Wood ProductsUsing a Large Chamber2.2 HUD Document:24 CFR 3280,Manufactured Home Construction and SafetyStandards,Federal Register,Vol 49,No.15532.3 NIOSH Document:Formaldehyde Method 3500,U.S.Department of Health,and Human Services32.4 Other Documents:Minnesota Statutes Section 1
12、44.495,325F.18,and 325F.181,Formaldehyde Gases in Building Materials4CaliforniaAir Resources Board(CARB),California Code ofRegulations Sections 93120-93120.12,Title 17 AirborneToxic Control Measure to Reduce Formaldehyde Emis-sions from Composite Wood Products51This test method is under the jurisdic
13、tion of ASTM Committee D07 on Woodand is the direct responsibility of Subcommittee D07.03 on Panel Products.Current edition approved Aug.1,2014.Published September 2014.Originallyapproved in 1994.Last previous edition approved in 2006 as D5582 00(2006).DOI:10.1520/D5582-14.2For referenced ASTM stand
14、ards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from Standardization Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,P
15、hiladelphia,PA19111-5098,http:/www.dodssp.daps.mil.4Available from Print Communications,Dept.ofAdministration,117 UniversityAve.,St.Paul,MN 55155.5Available from California EPA website:http:/www.arb.ca.gov/toxics/compwood/compwood.htm.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,We
16、st Conshohocken,PA 19428-2959.United States1 3.Significance and Use3.1 Limitations have been established on formaldehydeemission levels for wood panel building products made withurea-formaldehyde adhesives and permanently installed inhomes or used as components in kitchen cabinets and forsimilar industrial products.This test method is used in con-junction with the test method referenced by HUD Rules andRegulations 24 CFR 3280 for manufactured housing,Califor-nia Air Resources Board(CARB)regulati
