收藏 分享(赏)

ASTM_D_4662_-_15.pdf

上传人:益****师 文档编号:177410 上传时间:2023-03-04 格式:PDF 页数:3 大小:66.83KB
下载 相关 举报
ASTM_D_4662_-_15.pdf_第1页
第1页 / 共3页
ASTM_D_4662_-_15.pdf_第2页
第2页 / 共3页
ASTM_D_4662_-_15.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D466215Standard Test Methods forPolyurethane Raw Materials:Determination of Acid andAlkalinity Numbers of Polyols1This standard is issued under the fixed designation D4662;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,t

2、he year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope*1.1 These test methods measure the acidic and basic con-stituents in polyols and other materials of high acidity or

3、alkalinity that are soluble in mixtures of toluene and ethylalcohol.These test methods do not apply to polyethers.(SeeNote 1.)1.2 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro

4、-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.2.Referenced Documents2.1 ASTM Standards:2D883 Terminology Relating to PlasticsD1193 Specification for Reagent Water3.Terminology3.1 Defi

5、nitionsFor definitions of terms used in these testmethods see Terminology D883.3.2 Definitions of Terms Specific to This Standard:3.2.1 acid numberthe quantity of base,expressed in mil-ligrams of potassium hydroxide,that is required to titrate acidicconstituents present in 1 g of sample.3.2.2 alkali

6、nity numberthe quantity of base,expressed asmilligrams of potassium hydroxide,present in 1 g of sample.4.Summary of Test Method4.1 The sample is dissolved in a mixture of toluene andethyl alcohol.The resulting single-phase solution is titrated atroom temperature with alcoholic potassium hydroxidesol

7、ution,to the end point indicated by the color change ofadded phenolphthalein.Alkalinity numbers are determined byback-titration after adding excess hydrochloric acid.The end-point of these titrations also can be determined potentiometri-cally.5.Significance and Use5.1 These test methods are suitable

8、 for quality control,asspecification tests,and for research.The acid and alkalinitynumbers indicate the extent of a reaction with acids.The resultsare measures of batch-to-batch uniformity and are typicallyused as correction factors in calculating hydroxyl number.6.Reagents and Materials6.1 Purity o

9、f ReagentsUse reagent-grade chemicals in alltests.Unless otherwise indicated,it is intended that all reagentsconform to the specifications of the Committee on AnalyticalReagents of the American Chemical Society where suchspecifications are available.3Other grades are allowed,pro-vided it is first as

10、certained that the reagent is of sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determination.6.2 Purity of WaterUnless otherwise indicated,referencesto water shall be understood to mean reagent water as definedby Type I of Specification D1193.6.3 Ethyl Alcohol,95%.6.

11、4 Hydrochloric Acid(0.1 N)Prepare a 0.1 N solution ofhydrochloric acid(HCl).Standardization is unnecessary.6.5 Phenolphthalein Indicator SolutionDissolve 0.5 g ofphenolphthalein in 100 mL of a mixture of equal volumes ofwater and ethyl alcohol.Add a slight excess of 0.1 N NaOHsolution(pink color)and

12、 then just neutralize(colorless)with0.1 N HCl.1These test methods are under the jurisdiction of ASTM Committee D20 onPlastics and are the direct responsibility of Subcommittee D20.22 on CellularMaterials-Plastics and Elastomers.Current edition approved Sept.1,2015.Published September 2015.Originally

13、approved in 1987.Last previous edition approved in 2011 as D4662-08(2011)1.DOI:10.1520/D4662-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Su

14、mmary page onthe ASTM website.3Reagent Chemicals,American Chemical Society Specifications,AmericanChemical Society,Washington,DC.For suggestions on the testing of reagents notlisted by the American Chemical Society,see Analar Standards for LaboratoryChemicals,BDH Ltd.,Poole,Dorset,U.K.,and the Unite

15、d States Pharmacopeiaand National Formulary,U.S.Pharmacopeial Convention,Inc.(USPC),Rockville,MD.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.6 Potassium Hydroxide,Stan

16、dard Alcoholic Solution(0.1N)Dissolve 5.61 g of potassium hydroxide(KOH)in 10 mLof carbon dioxide-free water and dilute to 1 L with ethylalcohol.Store the solution in a chemical-resistant dispensingbottle protected by a guard tube containing soda-lime orascarite.Standardize frequently enough to detect changes of0.0005 N,preferably against pure potassium acid phthalate(KHC8H4O4,0.8 to 0.9 g)in about 100 mL of carbondioxide-free water,using phenolphthalein to detect the endpoint.6.7 Sodium Hydroxi

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2